參數資料
型號： C8051F012
廠商： Silicon Laboratories Inc
文件頁數： 19/171頁
文件大小： 0K
描述： IC 8051 MCU 32K FLASH 32LQFP
標準包裝： 250
系列： C8051F01x
核心處理器： 8051
芯體尺寸： 8-位
速度： 20MHz
連通性： SMBus（2 線/I²C），SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 8
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 4x10b; D/A 2x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 32-LQFP
包裝： 托盤
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.2.
Operation
A typical SMBus transaction consists of a START condition, followed by an address byte, one or more bytes of
data, and a STOP condition. The address byte and each of the data bytes are followed by an ACKNOWLEDGE bit
from the receiver. The address byte consists of a 7-bit address plus a direction bit. The direction bit (R/W)
occupies the least-significant bit position of the address. The direction bit is set to logic 1 to indicate a “READ”
operation and cleared to logic 0 to indicate a “WRITE” operation.
A general call address (0x00 +R/W) is
recognized by all slave devices allowing a master to address multiple slave devices simultaneously.
All transactions are initiated by the master, with one or more addressed slave devices as the target.
The master
generates the START condition and then transmits the address and direction bit. If the transaction is a WRITE
operation from the master to the slave, the master transmits the data a byte at a time waiting for an
ACKNOWLEDGE from the slave at the end of each byte. If it is a READ operation, the slave transmits the data
waiting for an ACKNOWLEDGE from the master at the end of each byte. At the end of the data transfer, the
master generates a STOP condition to terminate the transaction and free the bus. Figure 16.3 illustrates a typical
SMBus transaction.
Figure 16.3. SMBus Transaction
The SMBus interface may be configured to operate as either a master or a slave. At any particular time, it will be
operating in one of the following four modes:
16.2.1. Master Transmitter Mode
Serial data is transmitted on SDA while the serial clock is output on SCL. The first byte transmitted contains the
address of the target slave device and the data direction bit. In this case the data direction bit (R/W) will be logic 0
to indicate a “WRITE” operation. The master then transmits one or more bytes of serial data. After each byte is
transmitted, an acknowledge bit is generated by the slave. To indicate the beginning and the end of the serial
transfer, the master device outputs START and STOP conditions.
16.2.2. Master Receiver Mode
Serial data is received on SDA while the serial clock is output on SCL. The first byte is transmitted by the master
and contains the address of the target slave and the data direction bit. In this case the data direction bit (R/W) will
be logic 1 to indicate a “READ” operation.
Serial data is then received from the slave on SDA while the master
outputs the serial clock. The slave transmits one or more bytes of serial data. After each byte is received, an
acknowledge bit is transmitted by the master. The master outputs START and STOP conditions to indicate the
beginning and end of the serial transfer.
16.2.3. Slave Transmitter Mode
Serial data is transmitted on SDA while the serial clock is received on SCL. First, a byte is received that contains an
address and data direction bit. In this case the data direction bit (R/W) will be logic 1 to indicate a “READ”
operation. If the received address matches the slave’s assigned address (or a general call address is received) one or
more bytes of serial data are transmitted to the master.
After each byte is received, an acknowledge bit is
transmitted by the master. The master outputs START and STOP conditions to indicate the beginning and end of
the serial transfer.
START
SLAVE ADDR
R/W
ACK
DATA
ACK
DATA
NACK
STOP
Time
115
Rev. 1.7
相關PDF資料
PDF描述
PIC18LF6525-I/PT IC PIC MCU FLASH 24KX16 64TQFP
C8051F011 IC 8051 MCU 32K FLASH 48TQFP
C8051F010 IC 8051 MCU 32K FLASH 64TQFP
PIC32MX675F256L-80V/PF IC MCU 32BIT 256KB FLASH 100TQFP
C8051F006 IC 8051 MCU 32K FLASH 48TQFP
相關代理商/技術參數
參數描述
C8051F012/005 制造商:Silicon Laboratories Inc 功能描述:
C8051F012-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 32P MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F012-GQR 功能描述:8位微控制器 -MCU 32KB 10ADC 32Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F012-PX0005GQ 制造商:Silicon Laboratories Inc 功能描述:
C8051F012R 功能描述:8位微控制器 -MCU C 10Bit 32Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*