- 您現在的位置：買賣IC網 > PDF目錄378432 > C511-RN (SIEMENS A G) 8-Bit CMOS Microcontroller PDF資料下載
參數資料
| 型號： | C511-RN |
| 廠商： | SIEMENS A G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit CMOS Microcontroller |
| 中文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44 |
| 文件頁數： | 13/43頁 |
| 文件大?。?/td> | 692K |
| 代理商： | C511-RN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
C511 / C513
Semiconductor Group
13
Table 4
Pin Definitions and Functions in Programming Mode (C513A-H only)
Symbol
Pin Number
I/O*) Function
P-LCC-44
PRES
15
I
Programming Interface Reset
A high level on this input resets the programming interface and
its registers to their initial state.
AD0 - AD7 43 - 36
I/O
Bidirectional Address/Data Bus
AD0-7 is used to transfer data to and from the registers of the
programming interface and to read the data of the memory field
during EEPROM verification.
PALE
16
I
Programming Address Latch Enable
This input is used to latch address information at AD0-7. The
trailing edge of PALE is used to latch the register addresses.
Each read or write access in programming mode must be
initiated by a PALE high pulse.
PRD
18
I
Programming Read Control
A low level at this pin (and PCS=low) enables the AD0-7 buffers
for reading of the data or control registers of the programming
interface.
PWR
19
I
Programming Write Control
A low level at this pin (and PCS=low) causes the data at AD0-
7 to be written into the data or control registers of the
programming interface.
PCS
17
I
Programming Chip Select
A low level at this pin enables the access to the registers of the
programming interface. If PCS is active, either PRD or PWR
control whether data is read or written into the registers.
PCS should be always deactivated between subsequent
accesses to the programming interface.
XTAL2
20
–
XTAL2
Output of the inverting oscillator amplifier.
XTAL1
21
–
XTAL1
Input to the inverting oscillator amplifier and input to the internal
clock generator circuits.
To drive the device from an external clock source, XTAL1
should be driven, while XTAL2 is left unconnected.
During the
device programming a clock must be always supplied.
*) I = Input
O = Output
相關PDF資料 |
PDF描述 |
|---|---|
| C511A-RN | 8-Bit CMOS Microcontroller |
| C513-1RN | 8-Bit CMOS Microcontroller |
| C513A-2RN | 8-Bit CMOS Microcontroller |
| C513A-LM | 8-Bit CMOS Microcontroller |
| C513A-LN | 8-Bit CMOS Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C512 | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED |
| C51203-000 | 制造商:TE Connectivity 功能描述:TXR40AC90-1010BI |
| C5-12-15 | 制造商:Southco 功能描述:SEALED LEVER NON-LOCKING |
| C5122 | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:CB Transceiver PLL IC |
| C5-12-25 | 制造商:Southco 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。