- 您現在的位置：買賣IC網 > PDF目錄169426 > C-157-2500C-FDFB-SLC4 FIBER OPTIC TRANSCEIVER, 1565-1578nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR PDF資料下載
參數資料
| 型號： | C-157-2500C-FDFB-SLC4 |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 1565-1578nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 814K |
| 代理商： | C-157-2500C-FDFB-SLC4 |
8
2.5 Gbps Single Mode SFF LC Transceiver
C-1XX-2500(C)-FDFB-SLCX
20550 Nordhoff St. Chatsworth, CA 91311 tel: 818.773.9044 fax: 818.576.9486
9F, No 81, Shui Lee Rd. Hsinchu, Taiwan, R.O.C. tel: 886.3.5169222 fax: 886.3.5169213
LUMNDS851-Jul2005
rev. A.0
LUMINENTOIC.COM
EMI and ESC Consideration
Printed Circuit Board Layout Consideration
A ber-optic receiver employs a very high gain, wide bandwidth transimpedance amplier. This amplier detects and amplies signals
that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must be
used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing
of signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level,
high speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi lter be
used in both transmitter and receiver power supplies.
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs ush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to
chassis ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule,
the gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the
outside of the panel.
相關PDF資料 |
PDF描述 |
|---|---|
| C-151-2500-FDFB-SLC2 | FIBER OPTIC TRANSCEIVER, 1505-1518nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| C-131-2500-FDFB-SLC2 | FIBER OPTIC TRANSCEIVER, 1305-1318nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| C-131-2500C-FDFB-SLC2 | FIBER OPTIC TRANSCEIVER, 1305-1318nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| C-131-2500C-FDFB-SLC4 | FIBER OPTIC TRANSCEIVER, 1305-1318nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
| C-141-2500-FDFB-SLC4 | FIBER OPTIC TRANSCEIVER, 1405-1418nm, 2488Mbps(Tx), 2488Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C1572AAAAA | 制造商:Arcolectric 功能描述:SWITCH ROCKER DPDT (ON)-OFF 制造商:Arcolectric 功能描述:SWITCH, ROCKER, DPDT, (ON)-OFF-(ON); Contact Configuration:DPDT; Switch Operation:(On)-Off-(On); Contact Current Max:16A; Contact Voltage AC Nom:250V; Contact Voltage DC Nom:24V; Switch Mounting:Panel; Actuator / Cap Colour:Black; ;RoHS Compliant: Yes 制造商:Arcolectric 功能描述:DPDT blk (on)-off-(on) rockerswitch,125V |
| C1572AABB | 制造商:Arcolectric 功能描述:SWITCH ROCKER DPDT 16A 250 制造商:Arcolectric 功能描述:SWITCH, ROCKER, DPDT, 16A, 250VAC, BLACK; Contact Configuration:DPDT; Switch Operation:(On)-Off-(On); Contact Current Max:16A; Contact Voltage AC Nom:250V; Contact Voltage DC Nom:24V; Switch Mounting:Panel; Actuator / Cap Color:Black;RoHS Compliant: Yes 制造商:Arcolectric 功能描述:Switch Rocker Center OFF DP Quick Connect Rocker 16A 250VAC |
| C1572AABB-B | 功能描述:SWITCH ROCKER DPDT 16A 250V RoHS:是 類別:開關 >> 搖臂 系列:1550 標準包裝:1 系列:4000 電路:SPST-NC 開關功能:開-瞬時 額定電流:16A（AC） 額定電壓 - AC:125V 額定電壓 - DC:- 致動器樣式:凹面（彎曲） 顏色 - 致動器/蓋:紅 致動器標志:無標志 發光類型，顏色:- 發光電壓:- 安裝類型:面板安裝，卡入式 端接類型:快速連接 - 0.187"（4.7mm） 防護等級:- 特點:- 面板切口尺寸:長方形 - 19.20mm x 12.90mm 包裝:散裝 工作溫度:-20°C ~ 105°C 機械壽命:100,000 次循環 電氣壽命:25,000 次循環 其它名稱:Q6865357 |
| C1572AABR | 制造商:Arcolectric 功能描述: |
| C1572ALAAA | 制造商:Arcolectric 功能描述:SWITCH ROCKER DPDT (ON)-OFF 制造商:Arcolectric 功能描述:SWITCH, ROCKER, DPDT, (ON)-OFF-(ON) 制造商:Arcolectric 功能描述:SWITCH, ROCKER, DPDT, (ON)-OFF-(ON); Contact Configuration:DPDT; Switch Operation:(On)-Off-(On); Contact Current Max:16A; Contact Voltage AC Nom:250V; Contact Voltage DC Nom:24V; Switch Mounting:Panel; Actuator / Cap Colour:Black; ;RoHS Compliant: Yes 制造商:Arcolectric 功能描述:Black rocker switch,momentary centre off |
發布緊急采購，3分鐘左右您將得到回復。