- 您現在的位置：買賣IC網 > PDF目錄369560 > BUF20800 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels PDF資料下載
參數資料
| 型號： | BUF20800 |
| 英文描述： | 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
| 中文描述： | 18通道伽瑪雙通道可編程的VCOM電壓發生器 |
| 文件頁數： | 6/27頁 |
| 文件大?。?/td> | 765K |
| 代理商： | BUF20800 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
"#$%&%%
SBOS329D JUNE 2005 REVISED OCTOBER 2006
APPLICATIONS INFORMATION
The BUF20800 programmable voltage reference allows
fast, easy adjustment of 18 programmable reference
outputs and two channels for V
COM
adjustment, each with
10-bit resolution. It offers very simple, time-efficient
adjustment of the gamma reference and V
COM
voltages.
The BUF20800 is programmed through a high-speed,
standard, two-wire interface. The BUF20800 features a
double-register structure for each DAC channel to simplify
the implementation of dynamic gamma control. This
structure allows pre-loading of register data and rapid
updating of all channels simultaneously.
www.ti.com
6
Buffers 19 are able to swing to within 200mV of the
positive supply rail, and to within 0.6V of the negative
supply rail. Buffers 1018 are able to swing to within 0.8V
of the positive supply rail and to within 200mV of the
negative supply rail.
The BUF20800 can be powered using an analog supply
voltage from 7V to 18V, and a digital supply from 2V to
5.5V. The digital supply must be applied prior to or
simultaneously with the analog supply to avoid excessive
current and power consumption; damage to the device
may occur if it is left connected only to the analog supply
for extended periods of time. Figure 7 shows the power
supply timing requirements.
V
SD
GND
D
V
S
GND
Digital Supply:
Analog Supply:
t
1
: 0s minimum delay between Digital Supply and Analog Supply.
t
1
Figure 7. Power Supply Timing Requirements
Figure 8 shows the BUF20800 in a typical configuration.
In this configuration, the BUF20800 device address is 74h.
The output of each digital-to-analog converter (DAC) is
immediately updated as soon as data is received in the
corresponding register (LD = 0). For maximum dynamic
range, set V
REFH
= V
S
0.2V and V
REFL
= GND + 0.2V.
TWO-WIRE BUS OVERVIEW
The BUF20800 communicates through an industry-
standard, two-wire interface to receive data in slave mode.
This standard uses a two-wire, open-drain interface that
supports multiple devices on a single bus. Bus lines are
driven to a logic low level only. The device that initiates the
communication is called a master, and the devices
controlled by the master are slaves. The master generates
the serial clock on the clock signal line (SCL), controls the
bus access, and generates the START and STOP
conditions.
To address a specific device, the master initiates a START
condition by pulling the data signal line (SDA) from a HIGH
to a LOW logic level while SCL is HIGH. All slaves on the
bus shift in the slave address byte, with the last bit
indicating whether a read or write operation is intended.
During the 9th clock pulse, the slave being addressed
responds to the master by generating an Acknowledge
and pulling SDA LOW.
Data transfer is then initiated and eight bits of data are sent
followed by an Acknowledge Bit. During data transfer,
SDA must remain stable while SCL is HIGH. Any change
in SDA while SCL is HIGH will be interpreted as a START
or STOP condition.
Once all data has been transferred, the master generates
a STOP condition indicated by pulling SDA from LOW to
HIGH while SCL is HIGH.
The BUF20800 can act only as a slave device; therefore,
it never drives SCL. SCL is only an input for the BUF20800.
Table 1 and Table 2 summarize the address and
command codes, respectively, for the BUF20800.
ADDRESSING THE BUF20800
The address of the BUF20800 is 111010x, where
x
is the
state of the A0 pin. When the A0 pin is LOW, the device will
acknowledge on address 74h (1110100). If the A0 pin is
HIGH, the device will acknowledge on address 75h
(1110101).
Other valid addresses are possible through a simple mask
change. Contact your TI representative for information.
Table 1. Quick-Reference Table of BUF20800
Addresses
DEVICE/COMPONENT
BUF20800 Address:
A0 pin is LOW
(device will acknowledge on address 74h)
A0 pin is HIGH
(device will acknowledge on address 75h)
ADDRESS
1110100
1110101
Table 2. Quick-Reference Table of Command
Codes
COMMAND
CODE
Address byte of 00h followed by a data byte
of 06h.
00001xxx, with SCL
≤
400kHz; where
xxx
are bits unique to the Hs-capable master.
This byte is called the Hs master code.
General Call Reset
High-Speed Mode
相關PDF資料 |
PDF描述 |
|---|---|
| BUF20800AIDCPR | 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
| BUF20820 | 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
| BUF20820AIDCPR | 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
| BUF20820AIDCPRE4 | 18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
| BUF298AF | TRANSISTOR | BJT POWER MODULE | INDEPENDENT | 450V V(BR)CEO | 50A I(C) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BUF20800AIDCPR | 功能描述:LCD Gamma緩沖器 18-Ch Vltg Generator w/2 Prog VCOM Chs RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF20800AIDCPRE4 | 功能描述:LCD Gamma緩沖器 18-Ch Vltg Generator w/2 Prog VCOM Chs RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF20800ATDCPRQ1 | 功能描述:LCD Gamma緩沖器 AUTO CAT 18CH GAMMA VLTG GEN RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF20800-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:18-CHANNEL GAMMA VOLTAGE GENERATOR WITH TWO PROGRAMMABLE VCOM CHANNELS |
| BUF20820 | 制造商:BB 制造商全稱:BB 功能描述:18-Channel GAMMA VOLTAGE GENERATOR with Two Programmable VCOM Channels |
發布緊急采購，3分鐘左右您將得到回復。