參數資料
型號： BUF08800
英文描述： Programmable Reference Generator and 400mA VCOM Driver
中文描述： 可編程參考發電機驅動器和400mA威科姆
文件頁數： 12/23頁
文件大小： 627K
代理商： BUF08800
"#$%%$$
SBOS380A FEBRUARY 2007 REVISED MAY 2007
www.ti.com
12
OUTPUT LATCH
Because the BUF08800 features a double-buffered
register structure, updating a DAC register is not the same
as updating the DAC output voltage. There are three
methods for latching transferred data from the storage
registers into the DACs to update the DAC output voltage.
Method 1 requires externally setting the latch pin (LD) =
LOW, which updates each DAC output voltage whenever
its corresponding register is updated.
Method 2 externally sets LD = HIGH to allow all DAC
output voltages to retain their values during data transfer
and until LD = LOW, which simultaneously updates the
output voltages of all DACs to the new register values.
Method 3 uses software control. LD is maintained HIGH,
and all DACs are updated when the master writes a ‘1’ in
bit 15 of any DAC register. The update occurs after
receiving the 16-bit data for the currently-written register.
Use methods 2 and 3 to transfer a future data set into the
first bank of registers in advance to prepare for a very fast
update of DAC output voltages.
The General Call Reset and the power-up reset update the
DACs regardless of the state of the latch pin (LD).
REPLACEMENT OF TRADITIONAL GAMMA
BUFFER
Traditional gamma buffers rely on a resistor string (often
using expensive 0.1% resistors) to set the gamma
voltages. During development, the optimization of these
gamma voltages can be time-consuming. Programming
these gamma voltages with the BUF08800 can
significantly reduce the time required for gamma voltage
optimization. The final gamma values can be written into
the internal OTP memory to replace a traditional gamma
buffer solution. Figure 16a shows the traditional resistor
string; Figure 16b shows the more efficient alternative
method using the BUF08800.
The BUF08800 uses the most advanced high-voltage
CMOS process available today, allowing it to be
competitive with traditional gamma buffers.
Programmability offers the following advantages:
Shortens development time significantly.
Increases reliability by eliminating more than 18
external components.
Eliminates manufacturing variance between panels.
Allows a single panel to be built for multiple
customers, with loading of customer-dependent
gamma curves during final production. This method
significantly lowers inventory cost and risk, and
simplifies inventory management.
Allows demonstration of various gamma curves to
LCD monitor makers by simply uploading a different
set of gamma values.
Allows simple adjustment of gamma curves during
production to accommodate changes in the panel
manufacturing process or end-customer require-
ments.
Decreases cost and space.
V
COM
ADJUSTMENT
The output of the V
COM
digital-to-analog converter (DAC)
is internally connected to the input of the V
COM
buffer. As
a result of the high 10-bit resolution, the V
COM
voltage can
directly be adjusted without the need for external circuitry.
The integrated V
COM
driver can deliver up to 400mA of
peak current. In addition, the negative input is brought out
as a separate pin on the package to facilitate V
COM
compensation or equalization of the V
COM
voltage across
the panel (see Figure 17).
Traditional V
COM
adjustment uses a mechanical
potentiometer and a voltage divider for adjustment, as
shown in Figure 15. The programmable V
COM
channel
integrated in the BUF08800 is also able to use an external
voltage divider connected to +IN. It can be used to set the
initial V
COM
voltage as well as the adjustment range (see
Figure 17). Using this method, even at power-on the initial
V
COM
setting is close to the optimized V
COM
value, without
any programming. The external voltage divider also limits
the adjustment range that typically leads to a smaller
number of adjustment steps. In addition, the V
COM
output
voltage is limited only to the adjustment range, thereby
protecting the panel from undesirable V
COM
voltages.
V
COM
AVDD
R
A
R
B
R
C
Figure 15. Traditional V
Adjustment. External
voltage divider sets initial V
COM
voltage as well as
adjustment range.
The 10-bit DAC acts as a voltage source with a nominal
250k
output impedance; see Figure 17. For example, at
code 000h, the lowest V
COM
voltage is achieved because
the 250k
impedance is now in parallel with R
2
, which
lowers the impedance of the lower side of the voltage
divider. Consequently, code 3FFh results in the highest
adjustable V
COM
voltage.
However, an external voltage divider is not required for
correct function of the V
COM
channel integrated in the
BUF08800. Once the desired output level (that is,
minimum flicker) is obtained, the corresponding code can
be stored in the external EEPROM memory.
相關PDF資料
PDF描述
BUF11702PWP
BUF11705 22 - V Supply, 10 + 1 Channel Gamma Correction Buffer
BUF11705AIPWPR 22 - V Supply, 10 + 1 Channel Gamma Correction Buffer
BUF12800 REFERENCE VOLTAGE GENERATOR for LCD GAMMA CORRECTION
BUF12800AIPWP REFERENCE VOLTAGE GENERATOR for LCD GAMMA CORRECTION
相關代理商/技術參數
參數描述
BUF08800AIPWPR 功能描述:LCD Gamma緩沖器 Progr Ref Gen & 400mA Vcom Driver RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
BUF08800AIPWPRG4 功能描述:LCD Gamma緩沖器 Progr Ref Gen & 400mA Vcom Driver RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
BUF08821 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory
BUF08821A 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory
BUF08821AIPWPR 功能描述:LCD Gamma緩沖器 8 channel LCD Gamma Buffer RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*