- 您現在的位置：買賣IC網 > PDF目錄227779 > BU4337G-TR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 PDF資料下載
參數資料
| 型號： | BU4337G-TR |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | ROHS COMPLIANT, SSOP-5 |
| 文件頁數： | 11/11頁 |
| 文件大?。?/td> | 282K |
| 代理商： | BU4337G-TR |
Technical Note
9/10
BU42
□□G, BU42□□F, BU42□□FVE, BU43□□G, BU43□□F, BU43□□FVE series
www.rohm.com
2009.06 - Rev.B
2009 ROHM Co., Ltd. All rights reserved.
13.
Delay time (tPLH)
tPLH =
τ × RCT × CCT (sec)
τ: time constant
RCT : 10M
(typ.) (built-in resistor)
CCT : capacitor connected CT pin.
Recommended value of CCT capacitor is over 100pF.
The reference value
(
τ × RCT) ×10
6
VDET = 0.9 to 2.5V
Ta = 25°C
(min. = 5.1 × 10
6
typ.= 6.0 × 10
6
max = 6.9 × 10
6)
Ta = -25 to 125°C
(min. = 3.3 × 10
6
typ. = 6.0 × 10
6
max = 8.7 × 10
6)
VDET = 2.6 to 4.8V
Ta = 25°C
(min. = 5.9 × 10
6
typ.= 6.9 × 10
6
max = 7.9 × 10
6)
Ta = -25 to 125°C
(min. = 3.8 × 10
6
typ.= 6.9 × 10
6
max = 10.0 × 10
6)
14. External parameters
The recommended parameter range for CT is 100pF~0.1F. For RL, the recommended range is 50k
~1M. There
are many factors (board layout, etc) that can affect characteristics. Please verify and confirm using practical applications.
15. CT pin discharge
Due to the capabilities of the CT pin discharge transistor, the CT pin may not completely discharge when a short input
pulse is applied, and in this case the delay time may not be controlled. Please verify the actual operation.
16. Power on reset operation
Please note that the power on reset output varies with the Vcc rise up time. Please verify the actual operation.
17. Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC.
Therefore, be certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
18. When the power supply, is turned on because of in certain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
相關PDF資料 |
PDF描述 |
|---|---|
| BS1001-7PD2TB1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| BS1001-7PD3B1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| BS1001-7RD4 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| BS1001-9PD9TB1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| BS1001-9PV0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU4338 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Voltage Free Delay Time Setting CMOS Voltage Detector IC Series |
| BU4338F | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Voltage Detector IC with Adjustable Output Delay |
| BU4338F-TR | 功能描述:電壓監測器/監控器 LOW VOLT DETEC VOLT 4.0V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BU4338FVE | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Voltage Detector IC with Adjustable Output Delay |
| BU4338FVE-TR | 功能描述:電壓監測器/監控器 CMOS LOW VOLT DETEC RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。