- 您現在的位置：買賣IC網 > PDF目錄256251 > BU-61743G4-260L (DATA DEVICE CORP) 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 PDF資料下載
參數資料
| 型號： | BU-61743G4-260L |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| 封裝： | 25.40 X 25.40 MM, 3.94 MM HEIGHT, CERAMIC, FP-72 |
| 文件頁數： | 28/60頁 |
| 文件大?。?/td> | 700K |
| 代理商： | BU-61743G4-260L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
34
Data Device Corporation
www.ddc-web.com
BU-6174X/6184X/6186X
Rev. C
and Data Stack Rollover, Handshake Error, BC Retry, RT Address
Parity Error, Time Tag Rollover, RT Circular Buffer Rollover, BC
Message, RT Subaddress, BC End-of-Frame, Format Error, BC
Status Set, RT Mode Code, MT Trigger, and End-of-Message.
For the Enhanced Mini-ACE's Enhanced BC mode, there are
four user-defined interrupt bits. The BC Message Sequence
Control Engine includes an instruction enabling it to issue these
interrupts at any time.
For RT and Monitor modes, the Enhanced Mini-ACE architecture
includes an Interrupt Status Queue. This provides a mechanism
for logging messages that result in interrupt requests. Entries to
the Interrupt Status Queue may be filtered such that only valid
and/or invalid messages will result in entries on the queue.
The Enhanced Mini-ACE incorporates additional interrupt condi-
tions beyond ACE/Mini-ACE (Plus), based on the addition of
Interrupt Mask Register #2 and Interrupt Status Register #2. This
is accomplished by chaining the two Interrupt Status Registers
using the INTERRUPT CHAIN BIT (bit 0) in Interrupt Status
Register #2 to indicate that an interrupt has occurred in Interrupt
Status Register #1.
Additional interrupts include "Self-Test
Completed", masking bits for the Enhanced BC Control
Interrupts, 50% Rollover interrupts for RT Command Stack, RT
Circular Buffers, MT Command Stack, and MT Data Stack; BC
Op Code Parity Error, (RT) Illegal Command, (BC) General
Purpose Queue or (RT/MT) Interrupt Status Queue Rollover,
Call Stack Pointer Register Error, BC Trap Op Code, and the four
User-Defined interrupts for the Enhanced BC mode.
BUILT-IN TEST
A salient feature of the Enhanced Mini-ACE is its highly
autonomous self-test capability. This includes both protocol and
RAM self-tests. Either or both of these self-tests may be initiated
by command(s) from the host processor.
The protocol test consists of a comprehensive toggle test of the
terminal's logic. The test includes testing of all registers,
Manchester decoders, protocol logic, and memory management
logs. This test is completed in approximately 32,000 clock cycles.
That is, about 1.6 ms with a 20 MHz clock, 2.0 ms at 16 MHz, 2.7
ms at 12 MHz, and 3.2 ms at 10 MHz.
There is also a separate built-in test for the Enhanced Mini-
ACE's 4K X 16 or 64K X 16 shared RAM. This test consists of
writing and then reading/verifying the two walking patterns "data
= address" and "data = address inverted". This test takes 10
clock cycles per word. For an Enhanced Mini-ACE with 4K words
of RAM, this is about 2.0 ms with a 20 MHz clock, 2.6 ms at 16
MHz, 3.4 ms at 12 MHz, or 4.1 ms at 10 MHz. For an Enhanced
Mini-ACE with 64K words of RAM, this test takes about 32.8 ms
with a 20 MHz clock, 40.1 ms at 16 MHz, 54.6 ms at 12 MHz, or
65.6 ms at 10 MHz.
The Enhanced Mini-ACE built-in protocol test is performed auto-
matically at power-up. In addition, the protocol or RAM self-tests
may be initiated by a command from the host processor, via the
START/REST REGISTER. For RT mode, this may include the
host processor invoking self-test following receipt of an Initiate
self-test mode command. The results of the self-test are host
accessible by means of the BIT status register. For RT mode, the
result of the self-test may be communicated to the bus controller
via bit 8 of the RT BIT word ("0" = pass, "1" = fail).
Assuming that the protocol self-test passes, all of the register
and shared RAM locations will be restored to their state prior to
the self-test, with the exception of the 60 RAM address locations
0342-037D and the TIME TAG REGISTER. Note that for RT
mode, these locations map to the illegalization lookup table for
"broadcast transmit subaddresses 1 through 30" (non-mode
code subaddresses). Since MIL-STD-1553 does not define
these as valid command words, this section of the illegalization
lookup table is normally not used during RT operation. The TIME
TAG REGISTER will continue to increment during the self-test.
If there is a failure of the protocol self-test, it is possible to access
information about the first failed vector. This may be done by
means of the Enhanced Mini-ACE's upper registers (register
addresses 32 through 63). Through these registers, it is possible
to determine the self-test ROM address of the first failed vector,
the expected response data pattern (from the ROM), the register
or memory address, and the actual (incorrect) data value read
from register or memory. The on-chip self-test ROM is 4K X 24.
Note that the RAM self-test is destructive. That is, following the
RAM self-test, regardless of whether the test passes or fails, the
shared RAM is not restored to its state prior to this test. Following
a failed RAM self-test, the host may read the internal RAM to
determine which location(s) failed the walking pattern test.
RAM PARITY
The BC/RT/MT version of the Enhanced Mini-ACE is available
with options of 4K or 64K words of internal RAM. For the 64K
option, the RAM is 17 bits wide. The 64K X 17 internal RAM
allows for parity generation for RAM write accesses, and parity
checking for RAM read accesses. This includes host RAM
accesses, as well as accesses by the Enhanced Mini-ACE’s inter-
nal logic. When the Enhanced Mini-ACE detects a RAM parity
error, it reports it to the host processor by means of an interrupt
and a register bit. Also, for the RT and Selective Message Monitor
modes, the RAM address where a parity error was detected will
be stored on the Interrupt Status Queue (if enabled).
RELOCATABLE MEMORY MANAGEMENT LOCATIONS
In the Enhanced Mini-ACE's default configuration, there is a
fixed
area of shared RAM addresses, 0000h-03FF, that is allocated for
storage of the BC's or RT's pointers, counters, tables, and other
"non-message" data structures. As a means of reducing the
overall memory address space for using multiple Enhanced Mini-
ACEs in a given system (e.g., for use with the DMA interface
configuration), the Enhanced Mini-ACE allows this area of RAM
to be relocated by means of 6 configuration register bits. To pro-
vide backwards compatibility to ACE and Mini-ACE, the default
for this RAM area is 0000h-03FFh.
HOST PROCESSOR INTERFACE
The Enhanced Mini-ACE supports a wide variety of processor
interface configurations. These include shared RAM and DMA
configurations, straightforward interfacing for 16-bit and 8-bit
buses, support for both non-multiplexed and multiplexed
相關PDF資料 |
PDF描述 |
|---|---|
| BU-61743G4-260Q | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61743G4-520Z | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61743G4-580K | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61743G4-650K | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61743G4-760L | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU-61745 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |Enhanced Mini-ACE? |
| BU-61745F3-100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| BU-61745F3-110 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| BU-61745F4-100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| BU-61745F4-110 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。