- 您現在的位置：買賣IC網 > PDF目錄255847 > BU-61703G4-490L (DATA DEVICE CORP) 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 PDF資料下載
參數資料
| 型號： | BU-61703G4-490L |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| 封裝： | CERAMIC, QFP-72 |
| 文件頁數： | 32/54頁 |
| 文件大小： | 576K |
| 代理商： | BU-61703G4-490L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
38
Data Device Corporation
www.ddc-web.com
BU-61703/61705
D1 web-09/02-0
DETAILED MODE CODES FUNCTIONAL
DESCRIPTION
The applicable Mode Codes for the SSRT are described below:
DYNAMIC BUS CONTROL ( T/R = 1; 00000)
MESSAGE SEQUENCE = DBC + STATUS
The SSRT responds with Status showing non-acceptance of the mode code command.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No Status response. Set Message error bit (Status Word), High Word Count (BIT Word).
3. T/R bit Set to Zero. No Status response. Set Message Error bit (Status Word), Command Word Contents Error (BIT Word).
4. Zero T/R bit and Broadcast Address. No Status response. Set Message Error and Broadcast Received bits (Status Word),
Command Word Contents Error (BIT Word).
5. Broadcast Address. No Status response. Set Message Error and Broadcast Received bits (Status Word),
Command Word Contents Error (BIT Word).
SYNCHRONIZE WITHOUT DATA WORD ( T/R = 1; 00001)
MESSAGE SEQUENCE = SYNC + STATUS
The SSRT responds with Status.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No Status response. Set Message Error bit (Status Word), High Word Count (BIT Word).
3. T/R bit Set to Zero. No Status response. Set Message Error bit (Status Word), Command Word Contents Error (BIT Word).
4. Zero T/R bit and Broadcast Address. No Status response. Set Message Error and Broadcast Received bits (Status Word),
Command Word Contents Error (BIT Word).
TRANSMIT STATUS WORD ( T/R = 1; 00010)
MESSAGE SEQUENCE = TRANSMIT STATUS + STATUS
The Status register is not updated before it is transmitted and contains the resulting status from the previous command (assuming that it was not
a Transmit status or Transmit last command mode command).
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No Status response. Set Message Error bit (Status Word)
3. T/R bit Set to Zero. No Status response. Set Message Error bit (Status Word), Command Word Contents Error (BIT Word).
4. Zero T/R bit and Broadcast Address. No Status response. Set Message Error and Broadcast Received bits (Status Word),
Command Word Contents Error (BIT Word).
5. Broadcast Address. No Status response. Set Message Error and Broadcast Command Received bits (Status Word),
Command Contents Error (BIT Word).
INITIATE SELF-TEST ( T/R = 1; 00011)
MESSAGE SEQUENCE = SELF TEST + STATUS
If the command was non-broadcast, the SSRT responds with Status. If the command was either non-broadcast or broadcast, the SSRT will go
offline and perform its internal off-line protocol self-test. The self-test exercises the SSRT's encoder and decoders, registers, transmitter watchdog
timer, and protocol logic. This test is completed in approximately 32,000 clock cycles. That is, about 1.6 ms with a 20 MHz clock, 2.0 ms at 16
MHz, 2.7 ms at 12 MHz, and 3.2 ms at 10 MHz.
While the SSRT is performing its off-line self-test, it will ignore (and therefore not respond to) all messages received from the 1553 bus. The bus
controller may determine the result of the self-test by means of a Transmit BIT word mode command. If the self-test passes, bit 8 of the SSRT's
BIT word (BIT Test Fail) will be logic "0"; if the self-test fails, this bit will be logic "1". In addition, if self-test fails, the terminal flag status word bit will
be set to logic “1” in response to the next non-broadcast message.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No Status response. Set Message Error bit (Status Word), High Word Count (BIT Word).
3. T/R bit Set to Zero. No status response. Set Message Error bit (Status Word), Command Word Contents Error (BIT Word).
4. Zero T/R bit and Broadcast Address. No Status response. Set Message Error and Broadcast Command Received bits (Status word),
Command Word Contents Error (BIT Word).
5. Loopback Test Failure. Set Terminal Flag bit in internal Status register (Status Word for next non-broadcast command),
Current Channel (A or B) Loop Test Failure and CH A/B Loop Test Failure (BIT Word), assert RTFAIL output.
相關PDF資料 |
PDF描述 |
|---|---|
| BU-61703G4-500L | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61703G4-500W | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61703G4-590S | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61703G4-890L | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
| BU-61703G4-890Y | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU-61705 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |Simple System RT |
| BU-61740B3NEW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |μ-ACE (Micro-ACE?) |
| BU-61743 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |Enhanced Mini-ACE? |
| BU-61743F3-100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| BU-61743F3-110 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。