參數資料
型號: BTF1A16G-TR
英文描述: Dual Differential Transceiver BTF1A With Idle Bus Indicator
中文描述: 雙差分收發器BTF1A有空閑巴士指標
文件頁數: 1/16頁
文件大?。?/td> 252K
代理商: BTF1A16G-TR
Data Sheet
March 2001
Dual Differential Transceiver BTF1A
With Idle Bus Indicator
Features
Driver Features
I
Produces a logic zero in third state
I
400 mV difference voltage in third state
I
Two line drivers per package
I
Logic to convert TTL input logic levels to differen-
tial, pseudo-emmiter coupled logic (ECL) output
logic levels
I
No line loading when V
CC
= 0 V
I
High output driver for 50
loads
I
200 mA short-circuit current (typical)
I
2.0 ns maximum propagation delay
I
<0.2 ns output skew (typical)
Receiver Features
I
Two line receivers per package
I
High input impedance
8 k
I
Logic that converts differential input logic levels to
TTL output logic levels
I
4.0 ns maximum propagation delay
I
<0.20 V input sensitivity (typical)
I
1.2 V to
+
7.2 V common-mode range
Common Device Features
I
Common enable for each driver/receiver pair
I
Operating temperature range: –40
°
C to +125
°
C
(wider than the 41 Series)
I
Single 5.0 V
±
5% supply
I
400 Mbits/s maximum data rate
I
Meets enhanced small device interface (ESDI)
standards
I
Electrostatic discharge (ESD) performance better
than the 41 Series
I
Lower power requirement than the 41 Series
Description
The BTF1A device is a dual differential transceiver
circuit that transmits and receives digital data over
balanced transmission lines and is compatible with
Lucent Technologies Microelectronics Group differ-
ential drivers and receivers. It is designed to provide
a strong logic zero when in the third state. The mini-
mum difference voltage in the third state is 400 mV. It
is designed specifically for bus applications where a
well-defined logic state is needed when the bus is
idle. The driver puts out a logic
zero
when in the third
state mode, which is easily overriden by an active
buffer on the bus. When all the buffers on the bus are
inactive (third state), the signal on the bus is a
zero
indicating that the bus is idle.
The dual drivers translate input TTL logic levels to dif-
ferential pseudo-ECL output levels. The dual receiver
converts differential input logic levels to TTL output
levels. Each driver/receiver pair has its own common
enable control allowing serial data and a control clock
to be transmitted and received on a single integrated
circuit. The BTF1A transceiver requires the customer
to supply termination resistors on the circuit board.
The powerdown loading characteristics of the
receiver input circuit are approximately 8 k
relative
to the power supplies; hence, it will not load the
transmission line when the circuit is powered down.
For those circuits with termination resistors, the line
will remain impedance matched when the circuit is
powered down. The driver does not load the line
when it is powered down.
相關PDF資料
PDF描述
BTK1A Dual Differential Transceivers BTK1A and BTM1A
BTK1A16E Transient Voltage Suppressor Diodes
BTK1A16G Transient Voltage Suppressor Diodes
BTK1A16NB Transient Voltage Suppressor Diodes
BTK1A16P Transient Voltage Suppressor Diodes
相關代理商/技術參數
參數描述
BTF-2A-500 制造商:MERRIMAC 制造商全稱:MERRIMAC 功能描述:BIPHASE MODULATOR
BTF3050TEATMA1 功能描述:IC SWITCH SMART LOWSIDE 制造商:infineon technologies 系列:- 包裝:剪切帶(CT) 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:低端 輸出類型:N 通道 接口:開/關 電壓 - 負載:40V(最大) 電壓 - 電源(Vcc/Vdd):不需要 電流 - 輸出(最大值):3A 導通電阻(典型值):40 毫歐 輸入類型:非反相 特性:壓擺率受控型 故障保護:限流(固定),超溫,過壓 工作溫度:-40°C ~ 150°C(TJ) 封裝/外殼:TO-252-5,DPak(4 引線 + 接片),TO-252AD 供應商器件封裝:TO-252-5 標準包裝:1
BTF32C1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HC-49/US Microprocessor Crystals
BTF32C3 制造商:CALIBER 制造商全稱:Caliber Electronics Inc. 功能描述:HC-49/US Microprocessor Crystals
BTF32C5 制造商:CALIBER 制造商全稱:Caliber Electronics Inc. 功能描述:HC-49/US Microprocessor Crystals