- 您現在的位置：買賣IC網 > PDF目錄369509 > BT138X-500G Banana Plug; Current Rating:15A; Color:Black; Contact Plating:Nickel; Contact Termination:Screw Terminal PDF資料下載
參數資料
| 型號： | BT138X-500G |
| 英文描述： | Banana Plug; Current Rating:15A; Color:Black; Contact Plating:Nickel; Contact Termination:Screw Terminal |
| 中文描述： | 晶閘管產品目錄 |
| 文件頁數： | 180/224頁 |
| 文件大小： | 2697K |
| 代理商： | BT138X-500G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁當前第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁
AN1008
Application Notes
http://www.teccor.com
+1 972-580-7777
AN1008 - 2
2002 Teccor Electronics
Thyristor Product Catalog
I
T
: Current Rating
SCR
For RMS and average currents, the restricting factor is usually
confined so that the power dissipated during the on state and as
a result of the junction-to-case thermal resistance will not pro-
duce a junction temperature in excess of the maximum junction
temperature rating. Power dissipation is changed to RMS and
average current ratings for a 60 Hz sine wave with a 180° con-
duction angle. The average current for conduction angles less
than 180° is derated because of the higher RMS current con-
nected with high peak currents. The DC current rating is higher
than the average value for 180° conduction since no RMS com-
ponent is present.
The dissipation for non-sinusoidal waveshapes can be deter-
mined in several ways. Graphically plotting instantaneous dissi-
pation as a function of time is one method. The total maximum
allowable power dissipation (P
D
) may be determined using the
following equation for temperature rise:
where T
(max)
is the maximum rated junction temperature (at
zero rated current), T
C
is the actual operating case temperature,
and R
θ
JC
is the published junction-to-case thermal resistance.
Transient thermal resistance curves are required for short inter-
val pulses.
Triac
The limiting factor for RMS current is determined by multiplying
power dissipation by thermal resistance. The resulting current
value will ensure an operating junction temperature within maxi-
mum value. For convenience, dissipation is converted to RMS
current at a 360° conduction angle. The same RMS current can
be used at a conduction angle of less than 360°. For information
on non-sinusoidal waveshapes and a discussion of dissipation,
refer to the preceding description of SCR current rating.
I
TSM
: Peak Surge (Non-repetitive) On-state
Current — SCR and Triac
The peak surge current is the maximum peak current that may be
applied to the device for one full cycle of conduction without
device degradation. The maximum peak current is usually speci-
fied as sinusoidal at 50 Hz or 60 Hz. This rating applies when the
device is conducting rated current before the surge and, thus,
with the junction temperature at rated values before the surge.
The junction temperature will surpass the rated operating tem-
perature during the surge, and the blocking capacity may be
decreased until the device reverts to thermal equilibrium
.
The surge-current curve in Figure AN1008.3 illustrates the peak
current that may be applied as a function of surge duration. This
surge curve is not intended to depict an exponential current
decay as a function of applied overload. Instead, the peak current
shown for a given number of cycles is the maximum peak surge
permitted for that time period. The current must be derated so
that the peak junction temperature during the surge overload
does not exceed maximum rated junction temperature if blocking
is to be retained after a surge.
Figure AN1008.3
Peak Surge Current versus Surge Current Duration
I
TM
: Peak Repetitive On-state Current — SCR and Triac
The I
TM
rating specifies the maximum peak current that may be
applied to the device during brief pulses. When the device oper-
ates under these circumstances, blocking capability is main-
tained. The minimum pulse duration and shape are defined and
control the applied di/dt. The operating voltage, the duty factor,
the case temperature, and the gate waveform are also defined.
This rating must be followed when high repetitive peak currents
are employed, such as in pulse modulators, capacitive-discharge
circuits, and other applications where snubbers are required.
di/dt: Rate-of-change of On-state Current — SCR and Triac
The di/dt rating specifies the maximum rate-of-rise of current
through a thyristor device during turn-on. The value of principal
voltage prior to turn-on and the magnitude and rise time of the
gate trigger waveform during turn-on are among the conditions
under which the rating applies. If the rate-of-change of current
(di/dt) exceeds this maximum value, or if turn-on with high di/dt
during minimum gate drive occurs (such as dv/dt or overvoltage
events), then localized heating may cause device degradation.
During the first few microseconds of initial turn-on, the effect of
di/dt is more pronounced. The di/dt capability of the thyristor is
greatly increased as soon as the total area of the pellet is in full
conduction.
The di/dt effects that can occur as a result of voltage or transient
turn-on (non-gated) is not related to this rating. The di/dt rating is
specified for maximum junction temperature.
As shown in Figure AN1008.4, the di/dt of a surge current can be
calculated by means of the following equation.
As an example, surge current of 400 A at 60 Hz has a di/dt of
π
400/8.3 or 151.4 A/ms.
P
D
T
-----------------------------------
T
C
–
R
θ
JC
=
1
10
100
1000
10
20
30
40
50
60
80
100
250
300
400
1000
Surge Current Duration – Full Cycles
P
O
T
)
40 A TO-218
25 A T0-220
15 A TO-220
1) Gate control may be lost
during and immediately
following surge current interval.
2) Overload may not be repeated
until junction temperature has
returned to steady-state
rated value.
SUPPLY FREQUENCY: 60 Hz Sinusoidal
LOAD: Resistive
Maximum Rated Value at Specified
Case Temperature
Notes:
di
dt
----
π
I
-----------------
(
)
t
=
相關PDF資料 |
PDF描述 |
|---|---|
| BT138X-600G | Connector Adapter; Convert From:BNC Coaxial Jack; Convert To:Dual Banana Plugs |
| BT138X-800G | Connector Adapter; Convert From:BNC Coaxial Plug; Convert To:Dual Banana Plugs |
| BT139-800G | Thyristor Product Catalog |
| BT139F-500G | Thyristor Product Catalog |
| BT139X-500G | Thyristor Product Catalog |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BT138X-600 | 功能描述:雙向可控硅 RAIL TRIAC RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT138X-600,127 | 功能描述:雙向可控硅 RAIL TRIAC RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT138X-600/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRIAC 12A SOT-186A |
| bt138x-600127 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| BT138X-600D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12 A four-quadrant triacs, sensitive gate |
發布緊急采購，3分鐘左右您將得到回復。