- 您現在的位置：買賣IC網 > PDF目錄369507 > BT137-600E Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:Gray; Approval Bodies:UL, CSA; Approval Categories:UL AWM Styles 1007, 1565; CSA Types TR-64, TRSR-64; JQA-F; Passes VW-1 Flame Test RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | BT137-600E |
| 元件分類： | 三端雙向可控硅開關 |
| 英文描述： | Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:Gray; Approval Bodies:UL, CSA; Approval Categories:UL AWM Styles 1007, 1565; CSA Types TR-64, TRSR-64; JQA-F; Passes VW-1 Flame Test RoHS Compliant: Yes |
| 中文描述： | 晶閘管產品目錄 |
| 文件頁數： | 174/224頁 |
| 文件大小： | 2697K |
| 代理商： | BT137-600E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁當前第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁
AN1007
Application Notes
http://www.teccor.com
+1 972-580-7777
AN1007 - 2
2002 Teccor Electronics
Thyristor Product Catalog
Figure AN1007.3
Waveform Across Static Switch
A typical example would be in the application of this type circuit
for the control of 5 A resistive load with 120 V rms input voltage.
Choosing a value of 100
for R
1
and assuming a typical value of
1 V for the gate to MT1 (V
GT
) voltage, we can solve for V
P
by the
following:
V
P
= I
GT
(R
L
+ R
1
) + V
GT
Note: R
C
is not included since it is negligible.
V
P
= 0.025 (24 + 100) + 1.0 = 4.1 V
Additionally the turn-on angle is
θ
170V
PK
[
θ
= 1.4°]
The power lost by the turn-on angle is essentially zero. The
power dissipation in the gate resistor is very minute. A 100
,
0.25 W rated resistor may safely be used. The small turn-on
angle also ensures that no appreciable RFI is generated.
The relay circuit shown in Figure AN1007.1 and Figure AN1007.2
has several advantages in that it eliminates contact bounce,
noise, and additional power consumption by an energizing coil
and can carry an in-rush current of many times its steady state
rating.
The control device S
1
indicated can be either electrical or
mechanical in nature. Light-dependent resistors and light- acti-
vated semiconductors, optocoupler, magnetic cores, and mag-
netic reed switches are all suitable control elements. Regardless
of the switch type chosen, it must have a voltage rating equal to
or greater than the peak line voltage applied. In particular, the
use of hermetically sealed reed switches as control elements in
combination with triacs offers many advantages. The reed switch
can be actuated by passing DC current through a small coiled
wire or by the proximity of a small magnet. In either case, com-
plete electrical isolation exists between the control signal input,
which may be derived from many sources, and the switched
power output. Long life of the triac/reed switch combination is
ensured by the minimal volt-ampere switching load placed on the
reed switch by the triac triggering requirements. The thyristor rat-
ings determine the amount of load power that can be switched.
Normally Closed Circuit
With a few additional components, the thyristor can provide a
normally closed static switch function. The critical design portion
of this static switch is a clamping device to turn off/eliminate gate
drive and maintain very low power dissipation through the clamp-
ing component plus have low by-pass leakage around the power
thyristor device. In selecting the power thyristor for load require-
ments, gate sensitivity becomes critical to maintain low power
requirements. Either sensitive SCRs or sensitive logic triacs must
be considered, which limits the load in current capacity and type.
However, this can be broader if an extra stage of circuitry for gat-
ing is permitted.
Figure AN1007.4 illustrates an application using a normally
closed circuit driving a sensitive SCR for a simple but precise
temperature controller. The same basic principle could be applied
to a water level controller for a motor or solenoid. Of course, SCR
and diode selection would be changed depending on load current
requirements.
Figure AN1007.4
Normally Closed Temperature Controller
A mercury-in-glass thermostat is an extremely sensitive measur-
ing instrument, capable of sensing changes in temperature as
small as 0.1 °C. Its major limitation lies in its very low current-
handling capability for reliability and long life, and contact current
should be held below 1 mA. In the circuit of Figure AN1007.4, the
S2010LS2 SCR serves as both current amplifier for the Hg ther-
mostat and as the main load switching element.
With the thermostat open, the SCR will trigger each half cycle
and deliver power to the heater load. When the thermostat
closes, the SCR can no longer trigger and the heater shuts off.
Maximum current through the thermostat in the closed position is
less than 250 μA rms.
Figure AN1007.5 shows an all solid state, optocoupled, normally
closed switch circuit. By using a low voltage SBS triggering
device, this circuit can turn on with only a small delay in each half
cycle and also keep gating power low. When the optocoupled
transistor is turned on, the gate drive is removed with only a few
milliamps of bypass current around the triac power device. Also,
by use of the BS08D and 0.1 μF, less sensitive triacs and alter-
nistors can be used to control various types of high current loads.
120 V rms (170 V peak)
V
P
-
1 V rms or 1.6 V peak MAX
V
P
+
V
+
V
T
-
θ
Sin1
–
-----4.1
=
1000 W Heater Load
120 V ac
60 CPS
D2015L
CR
1
—CR
4
CR
4
CR
3
CR
1
CR
2
S2010LS2
0.1 μF
R
1
510 k
SCR
1
Twist Leads to Minimize
Pickup
Hg in Glass Thermostat
相關PDF資料 |
PDF描述 |
|---|---|
| BT137-600G | Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:Black; Approval Bodies:UL, CSA; Approval Categories:UL AWM Styles 1007, 1565; CSA Types TR-64, TRSR-64; JQA-F; Passes VW-1 Flame Test RoHS Compliant: Yes |
| BT137-800G | WIRE, PVC #22 BLACK* |
| BT137X-600D | Thyristor Product Catalog |
| BT136F-500 | Thyristor Product Catalog |
| BT136F-500D | DIODE ZENER SINGLE 500mW 13Vz 9.5mA-Izt 0.05 0.5uA-Ir 9.9Vr DO35-GLASS 5K/REEL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BT137-600E,127 | 功能描述:雙向可控硅 RAIL TRIAC RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT137-600E/DG | 功能描述:雙向可控硅 RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT137-600E/L01,127 | 功能描述:雙向可控硅 Thyristor TRIAC 600V 71A 3-Pin (3+Tab) RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT137-600E127 | 制造商:NXP Semiconductors 功能描述:TRIAC |
| BT137-600F | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triacs |
發布緊急采購，3分鐘左右您將得到回復。