- 您現在的位置：買賣IC網 > PDF目錄369508 > BT136S-500F (NXP SEMICONDUCTORS) Triacs PDF資料下載
參數資料
| 型號： | BT136S-500F |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 晶閘管 |
| 英文描述： | Triacs |
| 中文描述： | 500 V, 4 A, 4 QUADRANT LOGIC LEVEL TRIAC, TO-252 |
| 封裝： | PLASTIC, SOT-428, 3 PIN |
| 文件頁數： | 176/224頁 |
| 文件大?。?/td> | 2697K |
| 代理商： | BT136S-500F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁當前第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁
AN1007
Application Notes
http://www.teccor.com
+1 972-580-7777
AN1007 - 4
2002 Teccor Electronics
Thyristor Product Catalog
Figure AN1007.8
Optocoupler Circuit for Lower Current Inductive
Loads (Triac or Alternistor)
In this circuit, the series gate resistors are increased to 180
each, since a 240 V line is applied. Note that the load is placed
on the MT1 side of the power triac to illustrate that load place-
ment is
not
important for the circuit to function properly.
Also note that with standard U.S. residential 240 V home wiring,
both sides of the line are hot with respect to ground (no neutral).
Therefore, for some 240 V line applications, it will be necessary
to have a triac switch circuit in both sides of the 240 V line input.
If an application requires back-to-back SCRs instead of a triac or
alternistor, the circuit shown in Figure AN1007.9 may be used.
Figure AN1007.9
Optocoupled Circuit for Heavy-duty Inductive Loads
All application comments and recommendations for optocoupled
switches apply to this circuit. However, the snubber network can
be applied only across the SCRs as shown in the illustration. The
optocoupler should be chosen for best noise immunity. Also, the
voltage rating of the optocoupler output triac must be equal to or
greater than the voltage rating of SCRs.
Summary of Random Turn-on Relays
As shown in Figure AN1007.10, if the voltage across the load is
to be phase controlled, the input control circuitry must be syn-
chronized to the line frequency and the trigger pulses delayed
from zero crossing every half cycle. If the series gate resistor is
chosen to limit the peak current through the opto-driver to less
than 1 A, then on a 120 V ac line the peak voltage is 170 V;
therefore, the resistor is 180
. On a 240 V ac line the peak volt-
age is 340 V; therefore, the resistor should be 360
. These gate
pulses are only as long as the device takes to turn on (typically,
5 μs to 6 μs); therefore, 0.25 W resistor is adequate.
Figure AN1007.10
Random Turn-on Triac Driver
Select the triac for the voltage of the line being used, the current
through the load, and the type of load. Since the peak voltage of
a 120 V ac line is 170 V, you would choose a 200 V (MIN) device.
If the application is used in an electrically noisy industrial envi-
ronment, a 400 V device should be used. If the line voltage to be
controlled is 240 V ac with a peak voltage of 340 V, then use at
least a 400 V rated part or 600 V for more design margin. Selec-
tion of the voltage rating of the opto-driver must be the same or
higher than the rating of the power triac. In electrically noisy
industrial locations, the dv/dt rating of the opto-driver and the
triac must be considered.
The RMS current through the load and main terminals of the triac
should be approximately 70% of the maximum rating of the
device. However, a 40 A triac should not be chosen to control a
1 A load due to low latching and holding current requirements.
Remember that the case temperature of the triac must be main-
tained at or below the current versus temperature curve specified
on its data sheet. As with all semiconductors the lower the case
temperature the better the reliability. Opto-driven gates normally
do not use a sensitive gate triac. The opto-driver can supply up to
1 A gate pulses and less sensitive gate triacs have better dv/dt
capability. If the load is resistive, it is acceptable to use a stan-
dard triac. However, if the load is a heavy inductive type, then an
alternistor triac, or back-to-back SCRs as shown in Figure
AN1007.9, is recommended. A series RC snubber network may
or may not be necessary when using an alternistor triac. Nor-
mally a snubber network is not needed when using an alternistor
because of its high dv/dt and dv/dt(c) capabilities. However,
latching network as described in Figure AN1007.8 may be
needed for low current load variations.
Zero Crossing Turn-on, Normally Open
Relay Circuits
When a power circuit is mechanically switched on and off
mechanically, generated high-frequency components are gener-
ated that can cause interference problems such as RFI. When
power is initially applied, a step function of voltage is applied to
the circuit which causes a shock excitation. Random switch
opening stops current off, again generating high frequencies. In
addition, abrupt current interruption in an inductive circuit can
lead to high induced-voltage transients.
The latching characteristics of thyristors are ideal for eliminating
interference problems due to current interruption since these
devices can only turn off when the on-state current approaches
zero, regardless of load power factor.
On the other hand, interference-free turn-on with thyristors
requires special trigger circuits. It has been proven experimen-
6
R
in
V
cc
1
180
G
240 V ac
MT2
MT1
2
180
0.1 μF
3
4
5
0.047 μF
3.3 k
Load
Rin
Vcc
1
G
120 V ac
2
3
0.1
μ
F
Load
6
4
5
100
K
A
100
G
A
K
NS-SCR
NS-
SCR
Triac or
Alternistor
MT2
0.1
μ
f
100
Load
MT1
Hot
Neutral
120/240 V ac
G
180
for 120 V ac
360
for 240 V ac
Input
Rin
1
6
5
4
3
2
Load could be here
instead of lower location
相關PDF資料 |
PDF描述 |
|---|---|
| BT136S-500G | Triacs |
| BT136S-600G | DIODE ZENER DUAL COMMON-ANODE 300mW 8.2Vz 5mA-Izt 0.05 0.1uA-Ir 6 SOT-23 3K/REEL |
| BT136S-800G | RECTIFIER SCHOTTKY SINGLE 0.5A 20V 5.5A-Ifsm 0.385Vf 0.25A-IR SOD-123 3K/REEL |
| BT137F-500 | DIODE SWITCHING DUAL-DUAL SERIES 75V 215mA-Io 200mW 4ns-trr SOT-363 3K/REEL |
| BT137F-500D | Thyristor Product Catalog |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BT136S-500G | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Triacs |
| BT136S500T/R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRIAC|500V V(DRM)|4A I(T)RMS|TO-252AA |
| BT136S-600 | 制造商:NXP Semiconductors 功能描述:Triac,600V,4A,BT136S-600 |
| BT136S-600 /T3 | 功能描述:雙向可控硅 TAPE13 TRIAC RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
| BT136S-600,118 | 功能描述:雙向可控硅 TAPE13 TRIAC RoHS:否 制造商:STMicroelectronics 開啟狀態 RMS 電流 (It RMS):16 A 不重復通態電流:120 A 額定重復關閉狀態電壓 VDRM:600 V 關閉狀態漏泄電流（在 VDRM IDRM 下）:5 uA 開啟狀態電壓: 保持電流（Ih 最大值）:45 mA 柵觸發電壓 (Vgt):1.3 V 柵觸發電流 (Igt):1.75 mA 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:TO-220AB |
發布緊急采購，3分鐘左右您將得到回復。