參數資料
型號： BQ4285LS-N
廠商： TEXAS INSTRUMENTS INC
元件分類： XO, clock
英文描述： 1 TIMER(S), REAL TIME CLOCK, PDSO24
封裝： SOIC-24
文件頁數： 23/30頁
文件大小： 1497K
代理商： BQ4285LS-N
AS
Address strobe input
AS serves to demultiplex the address/data
bus. The falling edge of AS latches the ad-
dress on AD0–AD7. This demultiplexing pro-
cess is independent of the CS signal. For DIP,
SOIC, and PLCC packages with MOT = VCC,
the AS input is provided a signal similar to
ALE in an Intel-based system.
DS
Data strobe input
For DIP, SOIC, and PLCC packages with
MOT=VSS, the DS input is provided a sig-
nal similar to RD, MEMR, or I/OR in an
Intel-based system. The falling edge on DS
is used to enable the outputs during a read
cycle.
For the PLCC package, when MOT = VCC,
DS controls data transfer during a
bq4285E/L bus cycle. During a read cycle,
the bq4285E/L drives the bus after the ris-
ing edge on DS. During a write cycle, the
falling edge on DS is used to latch write
data into the chip.
R/W
Read/write input
For DIP, SOIC, and PLCC packages with
MOT=VSS, R/W is provided a signal simi-
lar to WR, MEMW, or I/OW in an Intel-
based system.
The rising edge on R/W
latches data into the bq4285E/L.
For the PLCC package, when MOT = VCC,
the level on R/W identifies the direction of
data transfer. A high level on R/W indicates
a read bus cycle, whereas a low on this pin
indicates a write bus cycle.
INT
Interrupt request output
INT is an open-drain output. This allows
INT to be valid in battery-backup mode for
the alarm interrupt.
To use this feature,
INT must be connected to a power supply
other than VCC. INT is asserted low when
any event flag is set and the corresponding
event enable bit is also set. INT becomes
high-impedance whenever register C is read
(see the Control/Status Registers section).
RST
Reset input
The bq4285E/L is reset when RST is pulled
low.
When reset, INT becomes high-
impedance, and the bq4285E/L is not accessi-
ble. Table 4 in the Control/Status Registers
section lists the register bits that are cleared
by a reset.
Reset may be disabled by connecting RST to
VCC. This allows the control bits to retain their
states through power-down/power-up cycles.
SQW
Square-wave output
SQW may output a programmable fre-
quency square-wave signal during normal
(VCC valid) system operation. Any one of
the 13 specific frequencies may be selected
through register A.
This pin is held low
when the square-wave enable bit (SQWE)
in register B is 0 (see the Control/Status
Registers section).
A 32.768kHz output is enabled by setting
the SQWE bit in register B to 1 and the
32KE bit in register C to 1 after setting
OSC2–OSC0 in register A to 011 (binary).
BC
3V backup cell input
BC should be connected to a 3V backup cell
for RTC operation and storage register non-
volatility in the absence of power. When VCC
slews down past VBC (3V typical), the inte-
gral control circuitry switches the power
source to BC. When VCC returns above VBC,
the power source is switched to VCC.
Upon power-up, a voltage within the VBC
range must be present on the BC pin for
the oscillator to start up.
X1–X2
Crystal inputs
The X1–X2 inputs are provided for an ex-
ternal 32.768Khz quartz crystal, Daiwa
DT-26 or equivalent, with 6pF load capaci-
tance. A trimming capacitor may be neces-
sary for extremely precise time-base gen-
eration.
CEIN
External RAM chip enable input,
active low
CEIN should be driven low to enable the
controlled external RAM. CEIN is internally
pulled up with a 50K
resistor.
CEOUT
External RAM chip enable output,
active low
When power is valid, CEOUT reflects CEIN.
VOUT
Supply output
VOUT provides the higher of VCC or VBC,
switched internally, to supply external RAM.
VCC
Positive power supply
VSS
Ground
3
Jan. 1999 B
bq4285E/L
相關PDF資料
PDF描述
BQ4285LSNTR 1 TIMER(S), REAL TIME CLOCK, PDSO24
BX80616I5650SLBLK 64-BIT, 133 MHz, MICROPROCESSOR, PBGA1156
BP83C51FA 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PDIP40
BU2465F 4-BIT, MROM, 1 MHz, MICROCONTROLLER, PDSO18
BU2419F-T1 4-BIT, MROM, 1 MHz, MICROCONTROLLER, PDSO22
相關代理商/技術參數
參數描述
BQ4285LSTR 制造商:TI 制造商全稱:Texas Instruments 功能描述:Enhanced RTC With NVRAM Control
BQ4285P- 制造商:TI 制造商全稱:Texas Instruments 功能描述:Real-Time Clock RTC With NVRAM Control
BQ4285P-SB2 功能描述:實時時鐘 RTC IC: 114x8 NVSRAM & NVSRAM Control RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
BQ4285Q- 制造商:TI 制造商全稱:Texas Instruments 功能描述:Real-Time Clock RTC With NVRAM Control
BQ4285S- 制造商:TI 制造商全稱:Texas Instruments 功能描述:Real-Time Clock RTC With NVRAM Control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*