- 您現在的位置：買賣IC網 > PDF目錄369480 > BQ2201PN-N Fast Recovery Bridge Rectifiers PDF資料下載
參數資料
| 型號： | BQ2201PN-N |
| 英文描述： | Fast Recovery Bridge Rectifiers |
| 中文描述： | 非易失控制器 |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 154K |
| 代理商： | BQ2201PN-N |
As the supply continues to fall past V
PFD
, an internal
switching device forces V
OUT
to one of the two external
backup energy sources. CE
CON
is held high by the V
OUT
energy source.
During power-up, V
OUT
is switched back to the V
CC
sup-
ply as V
CC
rises above the backup cell input voltage
sourcing V
OUT
. The CE
CON
output is held inactive for
time t
CER
(120 ms maximum) after the supply has
reached V
PFD
, independent of the CE input, to allow for
processor stabilization.
During power-valid operation, the CE input is fed
through to the CE
CON
output with a propagation delay
of less than 10ns. Nonvolatility is achieved by hardware
hookup,as shown in Figure 1.
Energy Cell Inputs—BC1,BC2
Two primary backup energy source inputs are provided
on the bq2201. The BC
1
and BC
2
inputs accept a 3V pri-
mary battery, typically some type of lithium chemistry.
If no primary cell is to be used on either BC
1
or BC
2
, the
unused input should be tied to V
SS
.
If both inputs are used, during power failure the V
OUT
output is fed only by BC
1
as long as it is greater than
2.5V. If the voltage at BC
1
falls below 2.5V, an internal
isolation switch automatically switches V
OUT
from BC
1
to BC
2
.
To prevent battery drain when there is no valid data to
retain, V
OUT
and CE
CON
are internally isolated from
BC
1
and BC
2
by either of the following:
I
Initial connection of a battery to BC
1
or BC
2
, or
I
Presentation of an isolation signal on CE.
A valid isolation signal requires CE low as V
CC
crosses
both V
PFD
and V
SO
during a power-down. See Figure 2.
Between these two points in time, CE must be brought
to the point of (0.48 to 0.52)*V
CC
and held for at least
700ns.
The isolation signal is invalid if CE exceeds
0.54*V
CC
at any point between V
CC
crossing V
PFD
and
V
SO
.
The appropriate battery is connected to V
OUT
and CE
CON
immediatelyonsubsequentapplicationandremovalofV
CC
.
2
FG220101.eps
VCC
CE
BC1
THS
VSS
VOUT
CECON
BC2
bq2201
VCC
CE
CMOS
SRAM
5V
From Address Decoder
3V
Primary
Cell
3V
Primary
Cell
Figure 1. Hardware Hookup (5% Supply Operation)
Oct. 1998 D
TD220101.eps
VCC
CE
VPFD
VSO
0.5 VCC
700ns
Figure 2. Battery Isolation Signal
bq2201
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| BQ2201S-N | Fast Recovery Bridge Rectifiers |
| BQ2201SN(NARROW) | Fast Recovery Bridge Rectifiers |
| BQ2201SN-N | Fast Recovery Bridge Rectifiers |
| BQ2212PN | Fast Recovery Bridge Rectifiers |
| BQ2212SN | Fast Recovery Bridge Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2201S | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SRAM Nonvolatile Controller Unit |
| BQ2201SN | 功能描述:存儲器控制器 SRAM Nonvolatile Controller IC RoHS:否 制造商:Maxim Integrated |
| BQ2201S-N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Nonvolatile Controller |
| BQ2201SN(NARROW) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Nonvolatile Controller |
| BQ2201SNG4 | 功能描述:存儲器控制器 SRAM Nonvolatile Controller IC RoHS:否 制造商:Maxim Integrated |
發布緊急采購，3分鐘左右您將得到回復。