- 您現在的位置：買賣IC網 > PDF目錄295161 > BQ20Z80DBT-V101 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO38 PDF資料下載
參數資料
| 型號： | BQ20Z80DBT-V101 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO38 |
| 封裝： | GREEN, PLASTIC, TSSOP-38 |
| 文件頁數： | 67/73頁 |
| 文件大?。?/td> | 1094K |
| 代理商： | BQ20Z80DBT-V101 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁
www.ti.com
FUNCTIONAL DESCRIPTION
OSCILLATOR FUNCTION
SYSTEM PRESENT OPERATION
GENERAL OPERATION
BATTERY PARAMETER MEASUREMENTS
bq20z80-V101
SLUS625D – SEPTEMBER 2004 – REVISED OCTOBER 2005
Within the functional description of the bq20z80 System Management Bus (SMBus), commands are prefixed with
SBS. and data flash variables are prefixed with DF: and are both italicized in full. For example:
SBS.RemainingCapacity( ) and DF:Fast Charge Current.
The oscillator of the bq20z80 can be set up for internal or external operation. On power up, the bq20z80
automatically attempts to start the internal oscillator. If a 100-k
resistor is not connected to ROSC (pin 33), then
it attempts to start the oscillator using an external 32.768-kHz crystal.
NOTE:
Install either the 100-k
ROSC resistor or the 12-pF, 32.768-kHz crystal. Do not
install both.
The performance of the internal oscillator depends on the tolerance of the 100-k
resistor between RSOC (pin
33) and VSSA (pin 34). Choose a resistor with a tolerance of
±0.1%, and 50-ppm or better temperature drift.
Place this resistor as close as possible to the bq20z80. If a 12-pF crystal is used, place it as close as possible to
the XCK1 (pin 34) and XCK2 (pin 33) pins. If not properly implemented, the PCB layout in this area can degrade
oscillator performance.
The bq20z80 periodically (1 s) pulls the PU output high. Connect this pin to the PRES pin of the bq20z80 via a
resistor of approximately 5 k
. The bq20z80 measures the PRES input during the PU-active period to determine
its state.
The bq20z80 detects that the battery is present in the system via a low state on the PRES input. When this
occurs, the bq20z80 enters normal operating mode and sets the PRES bit in SBS.OperationStatus( ). When the
pack is removed from the system and the PRES input is high, the bq20z80 enters the battery-removed state,
disabling the charge and discharge FETs, and enabling the 0-V/precharging FET. If DF:Operation Cfg B [NR] is
set, the PRES input is ignored and can be left floating.
NAME
CLASS / SUBCLASS
FORMAT
VALID RANGE
SIZE (BYTES)
UNITS
DEFAULT VALUE
Operation Cfg B
Configuration / Registers (64)
Hex
0x0000 to 0xffff
2
N/A
0x6140
The bq20z80 determines battery capacity by monitoring individual cell voltages and the amount of charge input
or removed from a rechargeable battery. In addition, the bq20z80 measures individual cell voltages, pack
voltage, temperature, and current using features of the bq29312A analog front end (AFE) device and calculates
individual cell impedances using collected data.
The bq20z80 measures charge/discharge activity by monitoring the voltage across a small-value series sense
resistor (5 m
to 20 m typ.) between the cell stack negative terminal and the negative terminal of the battery
pack. When an applications load is applied, impedance of each cell is measured by comparing its Open Circuit
Voltage (OCV) obtained for the present state of charge using a predefined OCV(SOC) function with measured
voltage under load.
The bq20z80 interfaces with the bq29312A to perform battery protection, cell balancing, and voltage translation
functions. The bq20z80 can accept inputs of up to two identical NTC thermistors (default is Semitec 103AT) for
temperature measurement, or can also be configured to use its internal temperature sensor. The bq20z80 uses
temperature to monitor the battery-pack environment.
The bq20z80 uses an integrating delta-sigma analog-to-digital converter (ADC) for current measurement, and a
second delta-sigma ADC for individual cell and battery voltage, and temperature measurement. The individual
cell and pack voltages, SBS.CellVoltagex( ), SBS.Voltage( ), SBS.Current( ), SBS.AverageCurrent( ), and
SBS.Temperature( ) are updated at 1-second intervals during normal operation.
7
相關PDF資料 |
PDF描述 |
|---|---|
| BQ2110LB-001 | DC-DC REG PWR SUPPLY MODULE |
| BQ24630RGET | SWITCHED CAPACITOR CONVERTER, PQCC24 |
| BQ25070DQCR | 1 A BATTERY CHARGE CONTROLLER, PDSO10 |
| BQ3285ESSNTR | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285ESS-N | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ20Z80DBT-V101G4 | 功能描述:電池管理 1% acc Gas Gauge for LiIon batterie RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V102 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V110 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V110G4 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80EVM-001 | 功能描述:電源管理IC開發工具 Impedance Track Fuel Gge LiIon Batt Packs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。