BP1045A 622.08 MHz SAW Filter
RF Monolithics, Inc.
4347 Sigma Road
Dallas, Texas 75244
USA
Phone: +1(972)233-2903
Fax: +1(972)387-8148
e-mail:
info@rfm.com
Home page:
www.rfm.com
European Sales Office
BP1045A 7/22/1999 R
Electrical Connections
Connection
Port 1 Hot
Port 1 Gnd Return
Port 2 Hot
Port 2 Gnd Return
Case Ground
Terminals
10
1
5
6
All Others
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
Max Soldering Profile
Value
+10
30
-40 to +85
265
°
C for 10 s
Units
dBm
VDC
°
C
Designed for SONET and SDH Clock Recovery
Low Insertion Loss
9.1 x 7.1 mm Surface-Mount Case
50
W
Input and Output
See Associated Plots
Characteristic
Center Frequency
Sym
fc
Min
Typ
Max
Units
MHz
Notes
1
622.080
Nominal
Center Frequency Limits
Insertion Loss at fc
Amplitude Variation
621.93
13.0
622.23
17.5
1.0
900
IL
15.5
1, 2
1, 2, 5
1, 2, 4
1, 2
dB
Q
3dB
BW
3
700
800
780
-0.33
—
kHz
°
/ kHz 1, 2, 6
°
dB
Passband
Loaded Q
3 dB Bandwidth
Transmission Phase Slope over 3 dB Bandwidth
Phase Deviation from Linear over 3 dB Bandwidth
Rejection
First Sidelobes (at approx. fc
±
1.6 MHz)
Ultimate (DC to 800 MHz, excluding main & first sidelobes)
Operating Temperature Range
10
1, 2, 7
1, 2, 3
25
28
-40
30
40
T
A
+85
°
C
1
Impedance Matching
Case Style
Lid Symbolization (YY = year, WW = week)
None to 50
Source and Load
SM9171-10 9.1 x 7.1 mm Nominal Footprint
RFM BP1045A YYWW
Notes:
1.
Unless noted otherwise, all specifications apply
over the operating temperature range
with filter soldered to the specified
demonstration board and measured with 50
network analyzer. Center frequency is defined as: ( f
3dB HIGH
- f
3dB LOW
) / 2.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent
on PCB layout and external impedance matching design. See Application Note No. 42 for details. Spurious responses may exceed
ultimate rejection specification at fc x1.6 and above.
Quality factor, Q, is defined as: Q
3dB
= fc / ( f
3dB HIGH
- f
3dB LOW
).
Amplitude variation is defined as the difference between the insertion loss at the baud frequency and filter’s minimum insertion loss.
Transmission phase slope is measured in the frequency domain and is calculated using a linear least-squares fit or straight-line
method over the 3 dB bandwidth.
Phase deviation from linear is specified over the 3 dB bandwidth. It is defined as the maximum residual deviation of the
transmission phase from linear least-square fit over the 3 dB bandwidth.
The design, manufacturing process, and specifications of this filter are subject to change.
Either Port 1 or Port 2 may be used for either input or output in the design.
10. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
11.
Copyright 1999, RF Monolithics Inc.
12. Electrostatic Sensitive Device. Observe precautions for handling.
2.
3.
4.
5.
6.
7.
8.
9.