- 您現在的位置：買賣IC網 > PDF目錄6123 > BD7562SFVM-TR (Rohm Semiconductor)OP AMP I/O FULL SWING HV 8-MSOP PDF資料下載
參數資料
| 型號： | BD7562SFVM-TR |
| 廠商： | Rohm Semiconductor |
| 文件頁數： | 15/18頁 |
| 文件大小： | 0K |
| 描述： | OP AMP I/O FULL SWING HV 8-MSOP |
| 特色產品： | CMOS Operational Amplifier |
| 標準包裝： | 1 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1 V/µs |
| 增益帶寬積： | 1MHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 900µA |
| 電流 - 輸出 / 通道： | 1mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 14.5 V，±2.5 V ~ 7.25 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VSSOP，8-MSOP（0.110"，2.80mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | BD7562SFVM-DKR BD7562SFVM-DKR-ND BD7562SFVMDKR |
www.rohm.com
TSZ02201-0RAR1G200250-1-2
2013 ROHM Co., Ltd. All rights reserved.
6/30
20.Sep.2013 Rev.001
TSZ2211115001
BD7561G
BD7561SG
BD7562xxx
BD7562Sxxx
Datasheet
Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also
shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or
general document.
1. Absolute maximum ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
(1) Supply Voltage (VDD/VSS)
Indicates the maximum voltage that can be applied between the VDD terminal and VSS terminal without
deterioration or destruction of characteristics of internal circuit.
(2) Differential Input Voltage (VID)
Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging
the IC.
(3) Input Common-mode Voltage Range (VICM)
Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration
or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
(4) Power Dissipation (PD)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25°C
(normal temperature). As for package product, Pd is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical characteristics
(1) Input Offset Voltage (VIO)
Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the
input voltage difference required for setting the output voltage at 0 V.
(2) Input Offset Current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
(3) Input Bias Current (IB)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
(4) Supply Current (IDD)
Indicates the current that flows within the IC under specified no-load conditions.
(5) Maximum Output Voltage(High) / Maximum Output Voltage(Low) (VOH/VOL)
Indicates the voltage range of the output under specified load condition. It is typically divided into maximum output
voltage high and low. Maximum output voltage high indicates the upper limit of output voltage. Maximum output
voltage low indicates the lower limit.
(6) Large Signal Voltage Gain (AV)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
AV = (Output voltage) / (Differential Input voltage)
(7) Input Common-mode Voltage Range (VICM)
Indicates the input voltage range where IC normally operates.
(8) Common-mode Rejection Ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. It is
normally the fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
(9) Power Supply Rejection Ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed.
It is normally the fluctuation of DC.
PSRR = (Change of power supply voltage)/(Input offset fluctuation)
(10) Output Source Current/ Output Sink Current (ISOURCE / ISINK)
The maximum current that can be output from the IC under specific output conditions. The output source current
indicates the current flowing out from the IC, and the output sink current indicates the current flowing into the IC.
(11) Slew Rate (SR)
Indicates the ratio of the change in output voltage with time when a step input signal is applied.
(12) Gain Bandwidth (GBW)
The product of the open-loop voltage gain and the frequency at which the voltage gain decreases 6dB/octave.
(13) Phase Margin (θ)
Indicates the margin of phase from 180 degree phase lag at unity gain frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| 0070.3521.A2 | VARISTOR 35V 7MM RADIAL |
| 0070.3511.A2 | VARISTOR 35V 5MM RADIAL |
| 0070.3021.A2 | VARISTOR 30V 7MM RADIAL |
| 302-R101 | CONN HEADER R/A 10POS GOLD |
| 0070.3011.A2 | VARISTOR 30V 5MM RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD7562SGE2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Voltage Operation CMOS Operational Amplifiers:Input/Output Full Swing |
| BD7562SGTR | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Voltage Operation CMOS Operational Amplifiers:Input/Output Full Swing |
| BD7562SVM | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Voltage Operation CMOS Operational Amplifiers:Input/Output Full Swing |
| BD-75F | 制造商:Distributed By MCM 功能描述:75 Ft BNC CCTV Installation Cables |
| BD7600FV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:マルチメディアLSI |
發布緊急采購，3分鐘左右您將得到回復。