- 您現在的位置：買賣IC網 > PDF目錄295139 > BD4837FVE 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 PDF資料下載
參數資料
| 型號： | BD4837FVE |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | ROHS COMPLIANT, VSOF-5 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 258K |
| 代理商： | BD4837FVE |
Technical Note
5/9
BD48
□□G, BD48□□FVE, BD49□□G, BD49□□FVE series
www.rohm.com
2009.04 - Rev.A
2009 ROHM Co., Ltd. All rights reserved.
Reference Data
Examples of Leading (TPLH) and Falling (TPHL) Output
Part Number
TPLH (
μs)
TPHL (
μs)
BD4845G/FVE
39.5
87.8
BD4945G/FVE
32.4
52.4
VDD=4.3V
5.1V
VDD=5.1V
4.3V
*This data is for reference only.
The figures will vary with the application, so please confirm actual operating conditions before use.
Explanation of Operation
For both the open drain type (Fig.12) and the CMOS output type (Fig.13), the detection and release voltages are used as
threshold voltages. When the voltage applied to the VDD pins reaches the applicable threshold voltage, the VOUT terminal
voltage switches from either “High” to “Low” or from “Low” to “High”. Because the BD48
□□G/FVE series uses an open drain
output type, it is possible to connect a pull-up resistor to VDD or another power supply [The output “High” voltage (VOUT) in
this case becomes VDD or the voltage of the other power supply].
Fig.12 (BD48
□□ Type Internal Block Diagram)
Fig.13 (BD49
□□ Type Internal Block Diagram)
Timing Waveform
Example: the following shows the relationship between the input voltages VDD and the output voltage VOUT when the
input power supply voltage VDD is made to sweep up and sweep down (the circuits are those in Fig.12 and 13).
1
When the power supply is turned on, the output is unsettled from
after over the operating limit voltage (VOPL) until TPHL. There fore it
is possible that the reset signal is not outputted when the rise time of
VDD is faster than TPHL.
2
When VDD is greater than VOPL but less than the reset release
voltage (VS +
VS), the output voltages will switch to Low.
3
If VDD exceeds the reset release voltage (VS +
VS), then
VOUT switches from L to H.
4
If VDD drops below the detection voltage (VS) when the power
supply is powered down or when there is a power supply fluctuation,
VOUT switches to L (with a delay of TPHL).
5
The potential difference between the detection voltage and the
release voltage is known as the hysteresis width (
VS). The system
is designed such that the output does not flip-flop with power supply
fluctuations within this hysteresis width, preventing malfunctions due
to noise.
Vref
R1
R2
VDD
GND
Q1
VOUT
R3
RL
Vref
R1
R2
R3
Q2
Q1
VDD
VOUT
GND
VDD
VDET+ΔVDET
VDET
VOPL
0V
TPHL
①
②
VOUT
TPLH
TPHL
TPLH
③
④
VOL
VOH
⑤
Fig.14
相關PDF資料 |
PDF描述 |
|---|---|
| BD538 | Complemetary Silicon Power Transistors(互補硅功率晶體管) |
| BD6637KV-E2 | DISK DRIVE MOTOR CONTROLLER, 1 A, PQFP64 |
| BD792 | 4 A, 100 V, PNP, Si, POWER TRANSISTOR, TO-225AA |
| BD9403KV | SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO14 |
| BD9781HFP-TR | 4 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PSSO7 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD4837FVE-TR | 功能描述:電壓監測器/監控器 CMOS DETEC VOLT 4.0V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BD4837G | 制造商:ROHM 制造商全稱:Rohm 功能描述:Voltage Detector IC |
| BD4837G-TR | 功能描述:電壓監測器/監控器 CMOS DETEC VOLT 3.7V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BD4838 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Standard CMOS Voltage Detector IC |
| BD4838FVE | 制造商:ROHM 制造商全稱:Rohm 功能描述:Voltage Detector IC |
發布緊急采購，3分鐘左右您將得到回復。