- 您現在的位置：買賣IC網 > PDF目錄369399 > BA15FP THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS PDF資料下載
參數資料
| 型號： | BA15FP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| 中文描述： | 三端固定電壓調節器 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 98K |
| 代理商： | BA15FP |
BAOOT / BAOOFP series
Regulator ICs
!
Operation notes
(1) Operating power supply voltage
When operating within the normal voltage range and within the ambient operating temperature range, most circuit
functions are guaranteed.
The rated values cannot be guaranteed for the electrical characteristics, but there are no sudden changes of the
characteristics within these ranges.
(2) Power dissipation
Heat attenuation characteristics are noted on a separate page and can be used as a guide in judging power
dissipation.
If these ICs are used in such a way that the allowable power dissipation level is exceeded, an increase in the chip
temperature could cause a reduction in the current capability or could otherwise adversely affect the performance of
the IC. Make sure a sufficient margin is allowed so that the allowable power dissipation value is not exceeded.
(3) Output oscillation prevention and bypass capacitor
Be sure to connect a capacitor between the output pin and GND to prevent oscillation. Since fluctuations in the valve
of the capacitor due to temperature changes may cause oscillations, a tantalum electrolytic capacitor with a small
internal series resistance (ESR) is recommended.
A 22
μ
F capacitor is recommended; however, be aware that if an extremely large capacitance is used (1000
μ
F or
greater), then oscillations may occur at low frequencies. Therefore, be sure to perform the appropriate verifications
before selecting the capacitor.
Also, we recommend connecting a 0.33
μ
F bypass capacitor as close as possible between the input pin and GND.
(4) Overcurrent protection circuit
An overcurrent protection circuit is built into the outputs, to prevent destruction of the IC in the even the load is shorted.
This protection circuit limits the current in the shape of a ’7’. This circuit is designed with a high margin, so that that
current is restricted and latching is prevented, even if a high-capacitance capacitator causes a large amount of current
to temporary flow through the IC.
However, these protection circuits are only good for pre-venting damage from sudden accidents and should not be
used for continuous protection (for instance, clamping at an output of 1V
F
or greater; below 1V
F
, the short mode circuit
operates). Note that the capacitor has negative temperature characteristics, and the design should take this into
consideration.
(5) Thermal overload circuit
A built-in thermal overload circuit prevents damage from overheating. When the thermal circuit is activated, the
outputs are turned OFF. When the temperature drops back to a constant level, the circuit is restored.
(6) Internal circuits could be damaged if there are modes in which the electric potential of the application’s input (V
CC
) and
GND are the opposite of the electric potential normally used by each of the outputs. Use of a diode or other such
bypass path is recommended.
(7) Although the manufacture of this product includes rigorous quality assurance procedures, the product may be
damaged if absolute maximum ratings for voltage or operating temperature are exceeded. If damage has occurred,
special modes (such as short circuit mode or open circuit mode) cannot be specified. If it is possible that such special
modes may be needed, please consider using a fuse or some other mechanical safety mea-sure.
(8) When used within a strong magnetic field, be aware that the possibility of malfunction exists.
相關PDF資料 |
PDF描述 |
|---|---|
| BA033FP | Low saturation voltage type 3-pin regulator |
| BA033T | Low saturation voltage type 3-pin regulator |
| BA033LBSG | Super-mini package regulator IC |
| BA033TFP | Low saturation voltage type 3-pin regulator |
| BA033SFP | Regulator, low drop-out type with ON/OFF switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA15FP-E2 | 功能描述:低壓差穩壓器 - LDO REGULATOR 15V 1A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BA-15G15UD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED LIGHT BAR & BAR GRAPH ARRAYS |
| BA15GA3MEFJ-E2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Automotive 300mA Variable Output LDO Regulator |
| BA-15H15UD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED LIGHT BAR & BAR GRAPH ARRAYS |
| BA15JC5 | 制造商:ROHM 制造商全稱:Rohm 功能描述:1.5A Variable/Fixed Output LDO Regulators |
發布緊急采購，3分鐘左右您將得到回復。