- 您現在的位置：買賣IC網 > PDF目錄369397 > BA07FP VOLT REGULATOR|FIXED|+7V|BIPOLAR|SIP|3PIN|PLASTIC PDF資料下載
參數資料
| 型號： | BA07FP |
| 英文描述： | VOLT REGULATOR|FIXED|+7V|BIPOLAR|SIP|3PIN|PLASTIC |
| 中文描述： | 電壓調節器|定額| 7伏|雙極|園區| 3針|塑料 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 187K |
| 代理商： | BA07FP |
34
Standard ICs
BA
T / FP series
Operation notes
(1)
Operating power supply voltage
When operating within the normal voltage range and
within the ambient operating temperature range, most
circuit functions are guaranteed.
The rated values cannot be guaranteed for the electrical
characteristics, but there are no sudden changes of the
characteristics within these ranges.
(2)
Power dissipation
Heat attenuation characteristics are noted on a separate
page and can be used as a guide in judging power dis-
sipation.
If these ICs are used in such a way that the allowable
power dissipation level is exceeded, an increase in the
chip temperature could cause a reduction in the current
capability or could otherwise adversely affect the perfor-
mance of the IC. Make sure a sufficient margin is allowed
so that the allowable power dissipation value is not ex-
ceeded.
(3)
Output oscillation prevention and bypass capacitor
Be sure to connect a capacitor between the output pin
and GND to prevent oscillation. Since fluctuations in the
valve of the capacitor due to temperature changes may
cause oscillations, a tantalum electrolytic capacitor with
a small internal series resistance (ESR) is recom-
mended.
A 22
μ
F capacitor is recommended; however, be aware
that if an extremely large capacitance is used (1000
μ
F
or greater), then oscillations may occur at low frequen-
cies. Therefore, be sure to perform the appropriate verifi-
cations before selecting the capacitor.
Also, we recommend connecting a 0.33
μ
F bypass ca-
pacitor as close as possible between the input pin and
GND.
(4)
Overcurrent protection circuit
An overcurrent protection circuit is built into the outputs,
to prevent destruction of the IC in the even the load is
shorted.
This protection circuit limits the current in the shape of a
’7’. This circuit is designed with a high margin, so that that
current is restricted and latching is prevented, even if a
high-capacitance capacitator causes a large amount of
current to temporary flow through the IC.
However, these protection circuits are only good for pre-
venting damage from sudden accidents and should not
be used for continuous protection (for instance, clamping
at an output of 1V
F
or greater; below 1V
F
, the short mode
circuit operates). Note that the capacitor has negative
temperature characteristics, and the design should take
this into consideration.
(5)
Thermal overload circuit
A built-in thermal overload circuit prevents damage from
overheating. When the thermal circuit is activated, the
outputs are turned OFF. When the temperature drops
back to a constant level, the circuit is restored.
(6)
Internal circuits could be damaged if there are
modes in which the electric potential of the application’s
input (V
CC
) and GND are the opposite of the electric po-
tential normally used by each of the outputs. Use of a
diode or other such bypass path is recommended.
(7)
Although the manufacture of this product includes
rigorous quality assurance procedures, the product may
be damaged if absolute maximum ratings for voltage or
operating temperature are exceeded. If damage has oc-
curred, special modes (such as short circuit mode or
open circuit mode) cannot be specified. If it is possible
that such special modes may be needed, please consid-
er using a fuse or some other mechanical safety mea-
sure.
(8)
When used within a strong magnetic field, be aware
that the possibility of malfunction exists.
相關PDF資料 |
PDF描述 |
|---|---|
| BA08FP | VOLT REGULATOR|FIXED|+8V|BIPOLAR|SIP|3PIN|PLASTIC |
| BA09FP | VOLT REGULATOR|FIXED|+9V|BIPOLAR|SIP|3PIN|PLASTIC |
| BA10FP | VOLT REGULATOR|FIXED|+10V|BIPOLAR|SIP|3PIN|PLASTIC |
| BA12FP | VOLT REGULATOR|FIXED|+12V|BIPOLAR|SIP|3PIN|PLASTIC |
| BA104 | DC to DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA07FP-E2 | 功能描述:IC REG LDO 7V 1A TO252-3 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:45 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:5V 輸入電壓:6 V ~ 30 V 電壓 - 壓降（標準）:0.47V @ 250mA 穩壓器數量:1 電流 - 輸出:250mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 產品目錄頁面:1289 (CN2011-ZH PDF) 其它名稱:*LP2954AIT*LP2954AIT/NOPBLP2954AIT |
| BA07SFP | 制造商:ROHM 制造商全稱:Rohm 功能描述:Regulator, low drop-out type with ON/OFF switch |
| BA07SFP-E2 | 功能描述:低壓差穩壓器 - LDO REG 7V 1A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BA07ST | 功能描述:低壓差穩壓器 - LDO REGULATOR 7V 1A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BA07T | 功能描述:低壓差穩壓器 - LDO REGULATOR 7V 1A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。