參數資料
型號: AWO25F24N-S
英文描述: HEADER,.100",4POS,641215-4-VP, GOLD,STR. POST,FRICTION LOCK
中文描述: 單輸出8磚:開放框架模塊
文件頁數: 7/13頁
文件大?。?/td> 382K
代理商: AWO25F24N-S
Technical Reference Notes
ALO25F24
(Single Output 8
th
Brick)
MODEL: ALO25F24
AUGUST 23, 2005 - REVISION H
SHEET 7 OF 13
Basic Operation and Features
(continued)
OUTPUT ENABLE
The converter comes with an Enable pin (PIN 2), which is primarily used to turn ON/OFF the converter. Both a Positive (no
“N” suffix required) and a Negative (suffix “N” required) Enable Logic options are being offered.
For Positive Enable, the converter is turned on when the Enable pin is at logic HIGH or left open. The unit turns off when the
Enable pin is at logic LOW or directly connected to -V
IN
. On the other hand, the Negative Enable version turns unit on when
the Enable pin is at logic LOW or directly connected to -V
IN
. The unit turns off when the Enable pin is at Logic HIGH.
OVER CURRENT PROTECTION (OCP)
The Over Current Protection is latching with auto-restart. The converter shuts down once the output current reaches the OCP
range. The converter will attempt to restart until the fault is removed. Latching OCP mode is available as an option (no model
part number assigned). This feature is only for module protection and no intention to customer application.
OUTPUT OVER VOLTAGE PROTECTION (OVP)
The Over Voltage Protection circuit is latching with auto-restart. The converter will latch-off and attempt to restart until the
fault is removed. Latching OVP mode is available as an option (no model part number assigned).
OVER TEMPERATURE PROTECTION (OTP)
The Over Temperature Protection circuit will shutdown the converter once the average PCB temperature reaches the OTP
range. This feature prevents the unit from overheating and consequently going into thermal runaway, which may further
damage the converter and the end system. Such overheating may be an effect of operation outside the given power thermal
derating conditions. Restart is possible once the temperature of the sensed location drops to less than 103
°
C.
REMOTE SENSE
The remote sense pins can be used to compensate for any voltage drops (per indicated max limits) that may occur along the
connection between the output pins to the load. Pin 7 (+Sense) and Pin 5 (-Sense) should be connected to Pin 8 (+Vout) and
Pin 4 (Return) respectively at the point where regulation is desired. The combination of remote sense and trim adjust cannot
exceed 110% of V
O
. When output voltage is trimmed up (through remote sensing and/or trim pin), output current must be
derated and maximum output power must not be exceeded.
相關PDF資料
PDF描述
AWO25F24-S HEADER,.100",5 POS,641215-5-VP ,GOLD,STR. POST,FRICTION LOCK
AWT906DS6 Telecommunication IC
AWT906S6 Logic IC
AWT908S6C Analog IC
AX1132 MEHRSCHRANK SCHMIERSYSTEM 6MIN
相關代理商/技術參數
參數描述
AWO25F24-S 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Single Output 8th Brick: Open-Frame Module
AWP 06-7240-T 制造商:Assmann Electronics Inc 功能描述:Conn IDC Connector SKT 6 POS 2.54mm IDT ST Cable Mount Tray
AWP 06-7540-T 功能描述:IDC SOCKET 2.54MM 6 CONTACTS 制造商:assmann wsw components 系列:- 包裝:托盤 零件狀態:在售 連接器類型:插口 觸頭類型:母形插口 針腳數:6 間距:0.100"(2.54mm) 排數:2 排距:0.100"(2.54mm) 安裝類型:自由懸掛 緊固類型:- 電纜端接:IDC 線纜類型:帶狀纜線 線規:- 特性:饋通,帶電極標記 觸頭鍍層:錫 觸頭鍍層厚度:- 顏色:灰色 標準包裝:264
AWP 06-8240-T 功能描述:IDC SOCKET 2.54MM 6 CONTACTS 制造商:assmann wsw components 系列:- 包裝:托盤 零件狀態:在售 連接器類型:插口 觸頭類型:母形插口 針腳數:6 間距:0.100"(2.54mm) 排數:2 排距:0.100"(2.54mm) 安裝類型:自由懸掛 緊固類型:- 電纜端接:IDC 線纜類型:帶狀纜線 線規:- 特性:饋通 觸頭鍍層:金 觸頭鍍層厚度:- 顏色:灰色 標準包裝:264
AWP 06-8540-T 功能描述:IDC SOCKET 2.54MM 6 CONTACTS 制造商:assmann wsw components 系列:- 包裝:托盤 零件狀態:在售 連接器類型:插口 觸頭類型:母形插口 針腳數:6 間距:0.100"(2.54mm) 排數:2 排距:0.100"(2.54mm) 安裝類型:自由懸掛 緊固類型:- 電纜端接:IDC 線纜類型:帶狀纜線 線規:- 特性:饋通 觸頭鍍層:錫 觸頭鍍層厚度:- 顏色:灰色 標準包裝:264