參數資料
型號： ATTINY44A-MFR
廠商： Atmel
文件頁數： 133/135頁
文件大小： 0K
描述： MCU AVR 4KB FLASH 20MHZ 20QFN
產品培訓模塊： MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 1
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 20MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 12
程序存儲器容量： 4KB（2K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 256 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-WFQFN 裸露焊盤
包裝： 標準包裝
其它名稱： ATTINY44A-MFRDKR
97
32015G–AVR32–09/09
AT32AP7001
11.5.4.1
Selecting PLL or oscillator for the main clock
The common main clock can be connected to Oscillator 0 or PLL0. By default, the main clock will
be connected to the Oscillator 0 output. The user can connect the main clock to the PLL0 output
by writing the PLLSEL bit in the Main Clock Control Register (MCCTRL) to 1. This must only be
done after PLL0 has been enabled, otherwise a deadlock will occur. Care should also be taken
that the new frequency of the synchronous clocks does not exceed the maximum frequency for
each clock domain.
11.5.4.2
Selecting synchronous clock division ratio
The main clock feeds an 8-bit prescaler, which can be used to generate the synchronous clocks.
By default, the synchronous clocks run on the undivided main clock. The user can select a pres-
caler division for the CPU clock by writing CKSEL:CPUDIV to 1 and CPUSEL to the prescaling
value, resulting in a CPU clock frequency:
f
CPU = fmain / 2
(CPUSEL+1)
Similarly, the clock for HSB, PBA, and PBB can be divided by writing their respective bitfields.
To ensure correct operation, frequencies must be selected so that f
CPU
f
HSB
f
PBA,B. Also, fre-
quencies must never exceed the specified maximum frequency for each clock domain.
CKSEL can be written without halting or disabling peripheral modules. Writing CKSEL allows a
new clock setting to be written to all synchronous clocks at the same time. It is possible to keep
one or more clocks unchanged by writing the same value a before to the xxxDIV and xxxSEL bit-
fields. This way, it is possible to e.g. scale CPU and HSB speed according to the required
performance, while keeping the PBA and PBB frequency constant.
11.5.4.3
Clock Ready flag
There is a slight delay from CKSEL is written and the new clock setting becomes effective. Dur-
ing this interval, the Clock Ready (CKRDY) flag in ISR will read as 0. If IER:CKRDY is written to
1, the Power Manager interrupt can be triggered when the new clock setting is effective. CKSEL
must not be re-written while CKRDY is 0, or the system may become unstable or hang.
11.5.5
Peripheral clock masking
By default, the clock for all modules are enabled, regardless of which modules are actually being
used. It is possible to disable the clock for a module in the CPU, HSB, PBA, or PBB clock
domain by writing the corresponding bit in the Clock Mask register (CPU/HSB/PBA/PBB) to 0.
When a module is not clocked, it will cease operation, and its registers cannot be read or written.
The module can be re-enabled later by writing the corresponding mask bit to 1.
A module may be connected to several clock domains, in which case it will have several mask
bits.
Table 11-1 contains a list of implemented maskable clocks.
11.5.5.1
Cautionary note
Note that clocks should only be switched off if it is certain that the module will not be used.
Switching off the clock for the internal RAM will cause a problem if the stack is mapped there.
Switching off the clock to the Power Manager (PM), which contains the mask registers, or the
corresponding PB bridge, will make it impossible to write the mask registers again. In this case,
they can only be re-enabled by a system reset.
相關PDF資料
PDF描述
ATTINY48-AUR MCU AVR 4KB FLASH 12MHZ 32TQFP
ATTINY48-MMUR MCU AVR 4KB FLASH 12MHZ 28MLF
ATTINY84A-MMHR MCU AVR 8K FLASH 20MHZ 3X3VQFN
ATTINY84V-10SSUR MCU AVR 8KB FLASH 10MHZ 14SOIC
ATTINY84V-10SSU MCU AVR 8K ISP FLASH 1.8V 14SOIC
相關代理商/技術參數
參數描述
ATTINY44A-MMH 功能描述:8位微控制器 -MCU 1.8V, 20MHz Industrial Temp RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44A-MMHR 功能描述:8位微控制器 -MCU 4KB FLSH 256B EE256B SRAM-20MHz, NiPdAu RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44A-MU 功能描述:8位微控制器 -MCU 1.8V, 20MHz Industrial Temp RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44A-MU SL383 制造商:Atmel Corporation 功能描述:MCU 8-bit ATtiny AVR RISC 4KB Flash 2.5V/3.3V/5V 20-Pin MLF EP T/R
ATTINY44A-MUR 功能描述:8位微控制器 -MCU 4KB FLSH 256B EE256B SRAM-20MHz, IND, RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*