- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS642LSHTN-I1-T (Allegro MicroSystems, Inc.) Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration PDF資料下載
參數資料
| 型號： | ATS642LSHTN-I1-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration |
| 中文描述： | 兩線真零速微型差分峰值檢測與校正連續齒輪齒傳感器 |
| 文件頁數： | 1/16頁 |
| 文件大?。?/td> | 430K |
| 代理商： | ATS642LSHTN-I1-T |
ATS642LSH
ATS642LSH-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
AB SO LUTE MAX MUM RAT NGS
Supply Voltage, V
CC
..........................................
28 V
Reverse-Supply Voltage, V
RCC
........................
–18 V
Operating Temperature
Ambient, T
A
,...............................
–40oC to 150oC
Maximum Junction, T
J(max)
........................
165oC
Storage Temperature, T
S
..................
–65oC to 170oC
Running mode calibration for continu-
ous optimization
Single chip IC for high reliability
Internal current regulator for 2-wire
operation
Small mechanical size (8 mm
diameter x 5.5 mm depth)
Precise duty cycle signal over
operating temperature range
Large operating air gaps
Automatic Gain Control (AGC)
for air
gap independent switchpoints
Automatic Offset Adjustment (AOA)
for signal processing optimization
True zero-speed operation
Undervoltage lockout
Wide operating voltage range
The ATS642LSH is an optimized Hall effect sensing integrated circuit and magnet
combination that provides a user-friendly solution for true zero-speed digital
gear-tooth sensing in two-wire applications. The sensor consists of a single-shot
molded plastic package that includes a samarium cobalt magnet, a pole piece,
and a Hall effect IC that has been optimized to the magnetic circuit. This small
package, with optimized two-wire leadframe, can be easily assembled and used in
conjunction with a wide variety of gear shapes and sizes.
The integrated circuit incorporates a dual element Hall effect sensor and signal
processing that switches in response to differential magnetic signals created
by ferrous gear teeth. The circuitry contains a sophisticated digital circuit to
reduce magnet and system offsets, to calibrate the gain for air gap independent
switchpoints, and to achieve true zero-speed operation. Signal optimization occurs
at power-up through the combination of offset and gain adjust and is maintained
throughout the operating time with the use of a running mode calibration. The run-
ning mode calibration allows immunity to environmental effects such as microos-
cillations of the target or sudden air gap changes.
The regulated current output is configured for two wire applications and the
sensor is ideally suited for obtaining speed and duty cycle information in ABS
(antilock braking systems). The 1.5 mm Hall element spacing is optimized for fine
pitch gear-tooth-based configurations. The package is lead (Pb) free, with 100%
matte tin leadframe plating.
Two-Wire True Zero Speed Miniature Differential
Peak-Detecting Gear Tooth Sensor with Continuous Calibration
Package SH, 4-pin Module
Features and Bene
fi
ts
1. VCC
2. No connection
3. Test pin (
fl
oat or tie to GND)
4. GND
1234
Use the following complete part numbers when ordering:
Part Number
I
CC
Typical
6.0 Low to 14.0 High mA
Packing*
ATS642LSHTN-I1-T
Tape and reel,
13-inch reel
800 pieces/reel
ATS642LSHTN-I2-T
7.0 Low to 14.0 High mA
*Contact Allegro for additional packing options.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS642LSHTN-I2-T | Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration |
| ATS643LSH-I2 | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSH | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSH-I1 | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSHTN-I1-T | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS642LSHTN-I1-T | 制造商:Allegro MicroSystems 功能描述:Hall Effect IC |
| ATS642LSHTN-I2-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS642LSHTN-I2-T | 制造商:Allegro MicroSystems 功能描述:Hall Effect IC |
| ATS643LSH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSH-I1 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
發布緊急采購，3分鐘左右您將得到回復。