- 您現在的位置：買賣IC網 > PDF目錄295113 > ATR0621P1-7FQY (ATMEL CORP) TELECOM, CELLULAR, BASEBAND CIRCUIT, PBGA100 PDF資料下載
參數資料
| 型號： | ATR0621P1-7FQY |
| 廠商： | ATMEL CORP |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | TELECOM, CELLULAR, BASEBAND CIRCUIT, PBGA100 |
| 封裝： | 9 X 9 MM, 0.80 MM PITCH, ROHS COMPLIANT, LFBGA-100 |
| 文件頁數： | 3/31頁 |
| 文件大?。?/td> | 477K |
| 代理商： | ATR0621P1-7FQY |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
11
4890C–GPS–10/06
ATR0621
3.3
Setting GPSMODE0 to GPSMODE12
The start-up configuration of a ROM-based system without external non-volatile memory is
defined by the status of the GPSMODE pins after system reset. Alternatively, the system can be
configured through message commands passed through the serial interface after start-up. This
configuration of the ATR0621 can be stored in an external non-volatile memory like FLASH
memory or EEPROM. Default designates settings used by ROM firmware if GPSMODE configu-
ration is disabled (GPSMODE0 =0).
In the case that GPSMODE pins with internal pull-up or pull-down resistors are connected to
GND/VDD18, additional current is drawn over these resistors. Especially GPSMODE3 can
impact the back-up current.
3.3.1
Enable GPSMODE Pin Configuration
If the GPSMODE configuration is enabled (GPSMODE0 = 1) and the other GPSMODE pins are
not connected externally, the reset default values of the internal pull-down and pull-up resistors
will be used.
Table 3-3.
GPSMODE Functions
Pin
Function
GPSMODE0 (P1)
Enable configuration with GPSMODE pins
GPSMODE1 (P9)
This pin (EXTINT0) is used for FixNow functionality and not used for GPSMODE
configuration
GPSMODE2 (P12)
GPS sensitivity settings
GPSMODE3 (P13)
GPSMODE4 (P14)
This pin (NAADET1) is used as active antenna supervisor input and not used for
GPSMODE configuration. This is the default selection if GPSMODE configuration is
disabled.
GPSMODE5 (P17)
Serial I/O configuration
GPSMODE6 (P19)
GPSMODE7 (P23)
USB power mode
GPSMODE8 (P24)
General I/O configuration
GPSMODE9 (P25)
This pin (NAADET0) is used as active antenna supervisor input and not used for
GPSMODE configuration
GPSMODE10 (P26)
General I/O configuration
GPSMODE11 (P27)
GPSMODE12 (P29) Serial I/O configuration
Table 3-4.
Enable Configuration with GPSMODE Pins
GPSMODE0
(Reset = PD)
Description
0(1)
Ignore all GPSMODE pins. The default settings as indicated below are used.
1
Use settings as specified with GPSMODE[2, 3, 5 to 8, 10 to 12]
Note:
1. Leave open
相關PDF資料 |
PDF描述 |
|---|---|
| ATR2805SF/CH | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| ATS650LSH-I2 | SPECIALTY ANALOG CIRCUIT |
| ATT-0293-83-SMA-02 | 0 MHz - 4000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| ATT-0640-10-29M-02 | 0 MHz - 40000 MHz RF/MICROWAVE FIXED ATTENUATOR |
| ATT-550F-00-35M-02 | 0 MHz - 26500 MHz RF/MICROWAVE FIXED ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATR0621P-7FHW | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:GPS Baseband GPS Baseband |
| ATR0621P-7FQY | 功能描述:IC GPS BASE PROCESSOR 100-LFBGA RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:- 標準包裝:100 系列:* |
| ATR0622 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:GPS Baseband Processor |
| ATR0622-DK1 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:GPS Baseband Processor |
| ATR0622-EK1 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:GPS Baseband Processor |
發布緊急采購，3分鐘左右您將得到回復。