參數資料
型號： AT91SAM9XE128-QU
廠商： Atmel
文件頁數： 10/159頁
文件大?。?/td> 0K
描述： MCU ARM9 128K FLASH 208-PQFP
產品培訓模塊： MCU Product Line Introduction
標準包裝： 24
系列： SAM9XE
核心處理器： ARM9
芯體尺寸： 16/32-位
速度： 180MHz
連通性： EBI/EMI，以太網，I²C，MMC，SPI，SSC，UART/USART，USB
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 96
程序存儲器容量： 128KB（128K x 8）
程序存儲器類型： 閃存
RAM 容量： 40K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 4x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 208-MQFP，208-PQFP
包裝： 托盤
配用： AT91SAM9XE-EK-ND - KIT EVAL FOR AT91SAM9XE
AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 105
PIC16F62X
14.9.1
WAKE-UP FROM SLEEP
The device can wake-up from SLEEP through one of
the following events:
1.
External RESET input on MCLR pin
2.
Watchdog Timer Wake-up (if WDT was enabled)
3.
Interrupt from RB0/INT pin, RB Port change, or
the Peripheral Interrupt (Comparator).
The first event will cause a device RESET. The two
latter events are considered a continuation of program
execution. The TO and PD bits in the STATUS register
can be used to determine the cause of device RESET.
PD bit, which is set on power-up is cleared when
SLEEP is invoked. TO bit is cleared if WDT Wake-up
occurred.
When the SLEEP instruction is being executed, the
next instruction (PC + 1) is pre-fetched. For the device
to
wake-up
through
an
interrupt
event,
the
corresponding interrupt enable bit must be set
(enabled). Wake-up is regardless of the state of the
GIE bit. If the GIE bit is clear (disabled), the device con-
tinues execution at the instruction after the SLEEP
instruction. If the GIE bit is set (enabled), the device
executes the instruction after the SLEEP instruction
and then branches to the interrupt address (0004h). In
cases where the execution of the instruction following
SLEEP
is not desirable, the user should have an NOP
after the SLEEP instruction.
The WDT is cleared when the device wakes-up from
SLEEP, regardless of the source of wake-up.
FIGURE 14-17:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
14.10 Code Protection
If
the
code
protection
bit(s)
have
not
been
programmed, the on-chip program memory can be
read out for verification purposes.
14.11 User ID Locations
Four memory locations (2000h-2003h) are designated
as user ID locations where the user can store
checksum or other code-identification numbers. These
locations are not accessible during normal execution
but are readable and writable during program/verify.
Only the Least Significant 4 bits of the user ID locations
are used.
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from SLEEP. The
SLEEP
instruction is completely executed.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(4)
INT pin
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
Instruction
Fetched
Instruction
Executed
PC
PC+1
PC+2
Inst(PC) = SLEEP
Inst(PC - 1)
Inst(PC + 1)
SLEEP
Processor in
SLEEP
Interrupt Latency
(Note 2)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy cycle
PC + 2
0004h
0005h
Dummy cycle
Tost(2)
PC+2
Note
1: XT, HS or LP Oscillator mode assumed.
2: TOST = 1024TOSC (drawing not to scale). Approximately 1
s delay will be there for ER Osc mode.
3: GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue
in-line.
4: CLKOUT is not available in these Osc modes, but shown here for timing reference.
Note:
The entire data EEPROM and FLASH
program memory will be erased when the
code protection is turned off. The INTRC
calibration data is not erased.
相關PDF資料
PDF描述
83-878 UHF RECEPTACLE REAR MOUNT PANEL
ADUC842BSZ62-3 IC ADC/DAC 12BIT W/MCU 52MQFP
AR215A222J4R CAP CER 2200PF 50V 5% RADIAL
ADUC842BSZ62-5 IC ADC/DAC 12BIT W/MCU 52-MQFP
082-4426-11RFX CONN PLUG N BELDEN 89880, 9880
相關代理商/技術參數
參數描述
AT91SAM9XE256 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE256B-CU 功能描述:IC MCU 32BIT 256KB FLASH 217BGA 制造商:microchip technology 系列:SAM9XE 包裝:托盤 零件狀態:在售 核心處理器:ARM9? 核心尺寸:16/32-位 速度:180MHz 連接性:EBI/EMI，以太網，I2C，存儲卡，SPI，SSC，UART/USART，USB 外設:欠壓檢測/復位，POR，PWM，WDT I/O 數:96 程序存儲容量:256KB（256K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:56K x 8 電壓 - 電源（Vcc/Vdd）:1.65 V ~ 1.95 V 數據轉換器:A/D 4x10b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:217-LFBGA 供應商器件封裝:217-BGA（15x15） 標準包裝:126
AT91SAM9XE256-CU 功能描述:ARM微控制器 - MCU BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM9XE256-QU 功能描述:ARM微控制器 - MCU PQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM9XE512 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*