參數資料
型號： AT91SAM7X512-AU-999
廠商： Atmel
文件頁數： 15/44頁
文件大?。?/td> 0K
描述： IC MCU ARM 512K HS FLASH 100LQFP
產品培訓模塊： SAM9 MPU Boot Solutions & Application Deployment
AT91SAM7X and SAM7XC Flash-based Microcontrollers
MCU Product Line Introduction
標準包裝： 1
系列： SAM7X
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 55MHz
連通性： CAN，以太網，I²C，SPI，SSC，UART/USART，USB
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 62
程序存儲器容量： 512KB（512K x 8）
程序存儲器類型： 閃存
RAM 容量： 128K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 標準包裝
其它名稱： AT91SAM7X512-AU-999DKR
22
6120GS–ATARM–07-Apr-11
SAM7X512/256/128 Summary
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 220 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.5.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.5.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.6
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high.
8.7
SAM-BA Boot Assistant
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in-
situ the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication via the DBGU or the USB Device
Port.
Communication via the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
Communication via the USB Device Port is limited to an 18.432 MHz crystal.
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
The SAM-BA Boot is in ROM and is mapped at address 0x0 when the GPNVM Bit 2 is set to 0.
When GPNVM bit 2 is set to 1, the device boots from the Flash.
When GPNVM bit 2 is set to 0, the device boots from ROM (SAM-BA).
相關PDF資料
PDF描述
VE-B43-IX-F2 CONVERTER MOD DC/DC 24V 75W
DS80C400-FNY+ IC MCU 75MHZ 16MB HP 100-LQFP
VE-B43-IX-F1 CONVERTER MOD DC/DC 24V 75W
DS89C450-ENL+ IC MCU FLASH 64KB 33MHZ 44-TQFP
VE-B43-IW-F3 CONVERTER MOD DC/DC 24V 100W
相關代理商/技術參數
參數描述
AT91SAM7X512B-AU 功能描述:ARM7? SAM7X Microcontroller IC 16/32-Bit 55MHz 512KB (512K x 8) FLASH 100-LQFP (14x14) 制造商:atmel 系列:SAM7X 包裝:托盤 零件狀態:有效 核心處理器:ARM7? 核心尺寸:16/32-位 速度:55MHz 連接性:CAN，以太網，I2C，SPI，SSC，UART/USART，USB 外設:欠壓檢測/復位，DMA，POR，PWM，WDT I/O 數:62 程序存儲容量:512KB（512K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:128K x 8 電壓 - 電源（Vcc/Vdd）:1.65 V ~ 1.95 V 數據轉換器:A/D 8x10b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:90
AT91SAM7X512B-AUR 功能描述:ARM7? SAM7X Microcontroller IC 16/32-Bit 55MHz 512KB (512K x 8) FLASH 100-LQFP (14x14) 制造商:atmel 系列:SAM7X 包裝:剪切帶（CT） 零件狀態:有效 核心處理器:ARM7? 核心尺寸:16/32-位 速度:55MHz 連接性:CAN，以太網，I2C，SPI，SSC，UART/USART，USB 外設:欠壓檢測/復位，DMA，POR，PWM，WDT I/O 數:62 程序存儲容量:512KB（512K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:128K x 8 電壓 - 電源（Vcc/Vdd）:1.65 V ~ 1.95 V 數據轉換器:A/D 8x10b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:1
AT91SAM7X512B-CU 功能描述:ARM7? SAM7X Microcontroller IC 16/32-Bit 55MHz 512KB (512K x 8) FLASH 100-TFBGA (9x9) 制造商:atmel 系列:SAM7X 包裝:托盤 零件狀態:有效 核心處理器:ARM7? 核心尺寸:16/32-位 速度:55MHz 連接性:CAN，以太網，I2C，SPI，SSC，UART/USART，USB 外設:欠壓檢測/復位，DMA，POR，PWM，WDT I/O 數:62 程序存儲容量:512KB（512K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:128K x 8 電壓 - 電源（Vcc/Vdd）:1.65 V ~ 1.95 V 數據轉換器:A/D 8x10b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:100-TFBGA 供應商器件封裝:100-TFBGA（9x9） 標準包裝:260
AT91SAM7X512B-CUR 功能描述:ARM7? SAM7X Microcontroller IC 16/32-Bit 55MHz 512KB (512K x 8) FLASH 100-TFBGA (9x9) 制造商:atmel 系列:SAM7X 包裝:剪切帶（CT） 零件狀態:有效 核心處理器:ARM7? 核心尺寸:16/32-位 速度:55MHz 連接性:CAN，以太網，I2C，SPI，SSC，UART/USART，USB 外設:欠壓檢測/復位，DMA，POR，PWM，WDT I/O 數:62 程序存儲容量:512KB（512K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:128K x 8 電壓 - 電源（Vcc/Vdd）:1.65 V ~ 1.95 V 數據轉換器:A/D 8x10b 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:100-TFBGA 供應商器件封裝:100-TFBGA（9x9） 標準包裝:1
AT91SAM7X512-CU 功能描述:ARM微控制器 - MCU 512kB Flash 128kB SRAM 55MHz 4 PWM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*