- 您現在的位置：買賣IC網 > PDF目錄11199 > AT91SAM7SE512-CU-999 (Atmel)IC MCU ARM7 512KB FLASH 144LFBGA PDF資料下載
參數資料
| 型號： | AT91SAM7SE512-CU-999 |
| 廠商： | Atmel |
| 文件頁數： | 24/47頁 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 512KB FLASH 144LFBGA |
| 產品培訓模塊： | MCU Product Line Introduction |
| 標準包裝： | 1,000 |
| 系列： | SAM7SE |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 連通性： | EBI/EMI，I²C，SPI，SSC，UART/USART，USB |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 88 |
| 程序存儲器容量： | 512KB（512K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 32K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 144-LFBGA |
| 包裝： | 帶卷 (TR) |
| 配用： | AT91SAM7SE-EK-ND - EVAL BOARD FOR AT91SAM7SE AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
30
6222GS–ATARM–6-Sep-11
SAM7SE512/256/32 Summary
9.1
Reset Controller
Based on one power-on reset cell and a double brownout detector
Status of the last reset, either Power-up Reset, Software Reset, User Reset, Watchdog
Reset, Brownout Reset
Controls the internal resets and the NRST pin output
Allows to shape a signal on the NRST line, guaranteeing that the length of the pulse meets
any requirement.
9.1.1
Brownout Detector and Power On Reset
The SAM7SE512/256/32 embeds one brownout detection circuit and a power-on reset cell. The
power-on reset is supplied with and monitors VDDCORE.
Both signals are provided to the Flash to prevent any code corruption during power-up or power-
down sequences or if brownouts occur on the VDDCORE power supply.
The power-on reset cell has a limited-accuracy threshold at around 1.5V. Its output remains low
during power-up until VDDCORE goes over this voltage level. This signal goes to the reset con-
troller and allows a full re-initialization of the device.
The brownout detector monitors the VDDCORE and VDDFLASH levels during operation by
comparing it to a fixed trigger level. It secures system operations in the most difficult environ-
ments and prevents code corruption in case of brownout on the VDDCORE or VDDFLASH.
When the brownout detector is enabled and VDDCORE decreases to a value below the trigger
level (Vbot18-, defined as Vbot18 - hyst/2), the brownout output is immediately activated.
When VDDCORE increases above the trigger level (Vbot18+, defined as Vbot18 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1s.
The VDDCORE threshold voltage has a hysteresis of about 50 mV, to ensure spike free brown-
out detection. The typical value of the brownout detector threshold is 1.68V with an accuracy of
± 2% and is factory calibrated.
When the brownout detector is enabled and VDDFLASH decreases to a value below the trigger
level (Vbot33-, defined as Vbot33 - hyst/2), the brownout output is immediately activated.
When VDDFLASH increases above the trigger level (Vbot33+, defined as Vbot33 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1s.
The VDDFLASH threshold voltage has a hysteresis of about 50 mV, to ensure spike free brown-
out detection. The typical value of the brownout detector threshold is 2.80V with an accuracy of
± 3.5% and is factory calibrated.
The brownout detector is low-power, as it consumes less than 20 A static current. However, it
can be deactivated to save its static current. In this case, it consumes less than 1A. The deac-
tivation is configured through the GPNVM bit 0 of the Flash.
9.2
Clock Generator
The Clock Generator embeds one low-power RC Oscillator, one Main Oscillator and one PLL
with the following characteristics:
RC Oscillator ranges between 22 KHz and 42 KHz
相關PDF資料 |
PDF描述 |
|---|---|
| NLVAS4599DTT1G | IC SWITCH SPDT 6TSOP |
| ADUC843BCP62Z-5 | IC MCU FLASH 12BIT ADC 56LFCSP |
| ADUC816BSZ-REEL | IC MCU FLASH 16BIT ADC 52MQFP |
| NLVAS4599DFT2G | IC SWITCH SPDT SC88 |
| ADUC845BSZ8-5-RL | IC FLASH MCU W/24BIT ADC 56-CSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT91SAM7SE-EK | 功能描述:開發(fā)板和工具包 - ARM Eval Kit for AT91SAM7SE device RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| AT91SAM7S-EK | 功能描述:開發(fā)板和工具包 - ARM Eval Kit for AT91SAM7S device RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| AT91SAM7X128 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers |
| AT91SAM7X128-AU | 功能描述:ARM微控制器 - MCU 128kB Flash 32kB SRAM 55MHz 4 PWM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7X128-AU-999 | 功能描述:ARM微控制器 - MCU Green, Ind Temp RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發(fā)布緊急采購，3分鐘左右您將得到回復。