參數資料
型號： AT45DB011B-XC
廠商： ATMEL CORP
元件分類： DRAM
英文描述： 1-MEGABIT 2.7 VOLT ONLY DATA FLASH
中文描述： 1M X 1 FLASH 2.7V PROM, PDSO14
封裝： 4.40 MM, PLASTIC, MO-153AB-1, TSSOP-14
文件頁數： 9/32頁
文件大小： 319K
代理商： AT45DB011B-XC
9
AT45DB011B
1984H–DFLSH–10/04
Operation Mode
Summary
The modes described can be separated into two groups – modes which make use of the Flash
memory array (Group A) and modes which do not make use of the Flash memory array
(Group B).
Group A modes consist of:
1.
Main Memory Page Read
2.
Main Memory Page to Buffer Transfer
3.
Main Memory Page to Buffer Compare
4.
Buffer to Main Memory Page Program with Built-in Erase
5.
Buffer to Main Memory Page Program without Built-in Erase
6.
Page Erase
7.
Block Erase
8.
Main Memory Page Program through Buffer
9.
Auto Page Rewrite
Group B modes consist of:
1.
Buffer Read
2.
Buffer Write
3.
Status Register Read
If a Group A mode is in progress (not fully completed), then another mode in Group A should
not be started. However, during this time in which a Group A mode is in progress (other than
Main Memory Page Read), Status Register Read from Group B can be started. Furthermore,
during Page Erase and Block Erase operation in progress from Group A, any of the modes
from Group B can be started.
Pin Descriptions
SERIAL INPUT (SI):
The SI pin is an input-only pin and is used to shift data into the device.
The SI pin is used for all data input, including opcodes and address sequences.
SERIAL OUTPUT (SO):
The SO pin is an output-only pin and is used to shift data out from the
device.
SERIAL CLOCK (SCK):
The SCK pin is an input-only pin and is used to control the flow of
data to and from the DataFlash. Data is always clocked into the device on the rising edge of
SCK and clocked out of the device on the falling edge of SCK.
CHIP SELECT (CS):
The DataFlash is selected when the CS pin is low. When the device is
not selected, data will not be accepted on the SI pin, and the SO pin will remain in a high-
impedance state. A high-to-low transition on the CS pin is required to start an operation, and a
low-to-high transition on the CS pin is required to end an operation.
WRITE PROTECT:
If the WP pin is held low, the first 256 pages of the main memory cannot
be reprogrammed. The only way to reprogram the first 256 pages is to first drive the protect
pin high and then use the program commands previously mentioned. If this pin and feature are
not utilized it is recommended that the WP pin be driven high externally.
相關PDF資料
PDF描述
AT45DB011B-XI 1-MEGABIT 2.7 VOLT ONLY DATA FLASH
AT45DB011B-XU 1-MEGABIT 2.7 VOLT ONLY DATA FLASH
AT45DB011D 1-megabit 2.7-volt DataFlash
AT45DB011D_07 1-megabit 2.7-volt DataFlash
AT45DB011D-MU 1-megabit 2.7-volt DataFlash
相關代理商/技術參數
參數描述
AT45DB011B-XI 功能描述:閃存 DATAFLASH 1M SERIAL 2.7V TSSOP IND TEMP RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AT45DB011B-XU 功能描述:閃存 1M SERIAL 2.7V - IND TEMP RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AT45DB011D 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1-megabit 2.7-volt Minimum DataFlash
AT45DB011D_07 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1-megabit 2.7-volt DataFlash
AT45DB011D_08 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1-megabit 2.7-volt Minimum DataFlash
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*