- 您現在的位置：買賣IC網 > PDF目錄381451 > AT45D021 (Atmel Corp.) 2-Megabit 5-volt Only Serial DataFlash PDF資料下載
參數資料
| 型號： | AT45D021 |
| 廠商： | Atmel Corp. |
| 英文描述： | 2-Megabit 5-volt Only Serial DataFlash |
| 中文描述： | 2兆位5伏只有串行的DataFlash |
| 文件頁數： | 2/18頁 |
| 文件大?。?/td> | 200K |
| 代理商： | AT45D021 |
AT45D021
2
noise, and reduces package size and active pin count. The
device is optimized for use in many commercial and indus-
trial applications where high density, low pin count, low
voltage, and low power are essential. Typical applications
for the DataFlash are digital voice storage, image storage,
and data storage. The device operates at clock frequencies
up to 10 MHz with a typical active read current consump-
tion of 15 mA.
To allow for simple in-system reprogrammability, the
AT45D021 does not require high input voltages for pro-
gramming. The device operates from a single power sup-
ply, 4.5V to 5.5V, for both the program and read
operations. The AT45D021 is enabled through the chip
select pin (CS) and accessed via a three-wire interface
consisting of the Serial Input (SI), Serial Output (SO), and
the Serial Clock (SCK).
All programming cycles are self-timed, and no separate
erase cycle is required before programming.
Block Diagram
Device Operation
The device operation is controlled by instructions from the
host processor. The list of instructions and their associated
opcodes are contained in Tables 1 and 2. A valid instruc-
tion starts with the falling edge of CS followed by the appro-
priate 8-bit opcode and the desired buffer or main memory
address location. While the CS pin is low, toggling the SCK
pin controls the loading of the opcode and the desired
buffer or main memory address location through the SI
(serial input) pin. All instructions, addresses, and data are
transferred with the most significant bit (MSB) first.
Read
By specifying the appropriate opcode, data can be read
from the main memory or from either one of the two data
buffers.
MAIN MEMORY PAGE READ:
A main memory read allows
the user to read data directly from any one of the 1024
pages in the main memory, bypassing both of the data buff-
ers and leaving the contents of the buffers unchanged. To
start a page read, the 8-bit opcode, 52H, is followed by 24
address bits and 32 don’t care bits. In the AT45D021, the
first five address bits are reserved for larger density
devices (see Notes on page 8), the next 10 address bits
(PA9-PA0) specify the page address, and the next nine
address bits (BA8-BA0) specify the starting byte address
within the page. The 32 don’t care bits which follow the 24
address bits are sent to initialize the read operation. Fol-
lowing the 32 don’t care bits, additional pulses on SCK
result in serial data being output on the SO (serial output)
pin. The CS pin must remain low during the loading of the
opcode, the address bits, and the reading of data. When
the end of a page in main memory is reached during a main
memory page read, the device will continue reading at the
beginning of the same page. A low to high transition on the
CS pin will terminate the read operation and tri-state the
SO pin.
BUFFER READ:
Data can be read from either one of the
two buffers, using different opcodes to specify which buffer
to read from. An opcode of 54H is used to read data from
buffer 1, and an opcode of 56H is used to read data from
buffer 2. To perform a buffer read, the eight bits of the
FLASH MEMORY ARRAY
PAGE (264 BYTES)
BUFFER 2 (264 BYTES)
BUFFER 1 (264 BYTES)
I/O INTERFACE
SCK
CS
RESET
V
CC
GND
RDY/BUSY
WP
SO
SI
相關PDF資料 |
PDF描述 |
|---|---|
| AT45D021-JC | 2-Megabit 5-volt Only Serial DataFlash |
| AT45D021-JI | 2-Megabit 5-volt Only Serial DataFlash |
| AT45D021-RC | 2-Megabit 5-volt Only Serial DataFlash |
| AT45D021-RI | 2-Megabit 5-volt Only Serial DataFlash |
| AT45D021-TC | 2-Megabit 5-volt Only Serial DataFlash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT45D021A | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-megabit 5-volt Only Serial DataFlash |
| AT45D021A-JC | 功能描述:閃存 2M bit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AT45D021A-JI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-megabit 5-volt Only Serial DataFlash |
| AT45D021A-RC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| AT45D021A-RI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。