- 您現在的位置：買賣IC網 > PDF目錄381451 > AT43USB326-AC (ATMEL CORP) Multimedia USB Keyboard Controller with Embedded Hub PDF資料下載
參數資料
| 型號： | AT43USB326-AC |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Multimedia USB Keyboard Controller with Embedded Hub |
| 中文描述： | 8-BIT, MROM, 12 MHz, RISC MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM THICKNESS, 0.50 MM PITCH, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 71/102頁 |
| 文件大小： | 511K |
| 代理商： | AT43USB326-AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
71
AT43USB326
3313D–USB–04/06
Set by hardware due to babble, physical disconnect or overcurrent except for Port 1 in which
case it is set by hardware at EOF2 due to hardware events. Cleared by firmware via Host
request ClearPortFeature(PORT_ENABLE).
Bit 0 – PCSC: Port Connect Status Change
0 = No change has occurred on Current Connect Status
1 = Current Connect Status has changed
This bit is set by hardware at EOF2 after it detects a connect or disconnect at a port, except for
Port 1. Hardware sets this bit for Port 5 after a hub reset. Cleared by firmware via Host request
ClearPortFeature(PORT_CONNECTION).
Hub and Port Power
Management
The embedded hub in a keyboard will most likely be a bus-powered hub even though the hard-
ware of the AT43USB326 is designed to accommodate both types of hubs. Management of
the downstream port power is also defined by the firmware: per port or global overcurrent
sensing, individual or gang power switching. While the interface to the external power supply
monitoring and switching is achieved through the microcontroller’s GPIO pins, the USB hard-
ware of the AT43USB326 contains the circuitry to handle all the possible combinations port
power management tasks.
Overcurrent Sensing
If programmed for global overcurrent protection, the AT43USB326 is capable of detecting an
overcurrent in its downstream port even while it is in the suspend state. This mode is enabled
through the Overcurrent Detect Register, UOVCER, which controls the PD0 pin used for over-
current input sensing.
1.
Global Overcurrent Protection
– In this mode, the Port Overcurrent Indicator and
Port Overcurrent Indicator Change should be set to 0's. For the AT43USB326 an exter-
nal solid state switch, such as the Micrel MIC2545-2, is required to switch power to the
external USB ports. The FLG# output of the switch should be connected to PD0. When
an overcurrent occurs, FLG# is asserted and the firmware should set the Hub Overcur-
rent Indicator and Hub Overcurrent Indicator Change and switch off power to the hub.
2.
Individual Port Over-current Protection
– The Hub Overcurrent Indicator and Hub
Overcurrent Indicator Change bits should be set to 0's. One MIC2026-2 is required for
the two USB ports. Each of the FLG# outputs of the MIC2026-2 should be connected
to an unused microcontroller port. An overcurrent is indicated by assertion of FLG#.
The firmware sets the corresponding port's Overcurrent Indicator and the Overcurrent
Indicator Change bits and switches off power to the port. At the next IN token from the
Host, the AT43USB326 reports the status change.
Port Power Switching
1.
Gang Power Switching
– One of the microcontroller I/O port pins must be pro-
grammed as an output to control the external switch, PWRN. Switch ON is requested
by the USB Host through the SetPortFeature(PORT_POWER) request. Switch OFF is
executed upon receipt of a ClearPortFeature(PORT_POWER) or upon detecting an
overcurrent condition. The firmware clears the Power Control Bit. Only if all of the
Power Control Bits of ports 2 and 3 are cleared should the firmware de-assert the
PWRN pin.
Individual Power Switching
– One microcontroller I/O port pin must be assigned for
each USB port to control the external switch, PWRxN, where x = 2, 3. Each of the
Power Control Bits controls one PWRxN.
Multiple Ganged Overcurrent Protection
– Overcurrent sensing is grouped physi-
cally into one or more gangs, but reported individually.
2.
3.
相關PDF資料 |
PDF描述 |
|---|---|
| AT43USB326-AU | Multimedia USB Keyboard Controller with Embedded Hub |
| AT43USB351M-AC | Full-speed/Low-speed USB Microcontroller with ADC and PWM |
| AT43USB353M-AC | Low Cost Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355E-AC | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
| AT43USB355E-AU | Full-speed USB Microcontroller with Embedded Hub, ADC and PWM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT43USB326-AU | 功能描述:USB 接口集成電路 USB KEYBOARD FOR LOGITECH - IND TEMP RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| AT43USB351M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Missed Watchdog Timer Reset |
| AT43USB351M_04 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed/ Low-speed USB Microcontroller with ADC and PWM |
| AT43USB351M-AC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Full-speed/ Low-speed USB Microcontroller with ADC and PWM |
| AT43USB353M | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Missed Watchdog Timer Reset |
發布緊急采購，3分鐘左右您將得到回復。