- 您現在的位置：買賣IC網 > PDF目錄381446 > AT29C010A-90TI (ATMEL CORP) High Speed CMOS Logic Octal Non-Inverting Buffers and Line Drivers with 3-State Outputs 20-TSSOP -55 to 125 PDF資料下載
參數資料
| 型號： | AT29C010A-90TI |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | High Speed CMOS Logic Octal Non-Inverting Buffers and Line Drivers with 3-State Outputs 20-TSSOP -55 to 125 |
| 中文描述： | 128K X 8 FLASH 5V PROM, 90 ns, PDSO32 |
| 封裝： | 8 X 20 MM, PLASTIC, MO-142BD, TSOP1-32 |
| 文件頁數： | 3/12頁 |
| 文件大小： | 727K |
| 代理商： | AT29C010A-90TI |
(continued)
Temperature Under Bias.................-55
°
C to +125
°
C
Storage Temperature......................-65
°
C to +150
°
C
All Input Voltages
(including NC Pins)
with Respect to Ground ................... -0.6V to +6.25V
All Output Voltages
with Respect to Ground .............-0.6V to V
CC
+ 0.6V
Voltage on OE
with Respect to Ground ................... -0.6V to +13.5V
*NOTICE: Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions beyond those indi-
cated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Absolute Maximum Ratings*
After the software data protection’s 3-byte command code
is given, a byte load is performed by applying a low pulse
on the WE or CE input with CE or WE low (respectively)
and OE high. The address is latched on the falling edge of
CE or WE, whichever occurs last. The data is latched by
the first rising edge of CE or WE. The 128-bytes of data
must be loaded into each sector by the same procedure as
outlined in the program section under device operation.
HARDWARE DATA PROTECTION:
Hardware features
protect against inadvertent programs to the AT29C010A
in the following ways: (a) V
CC
sense— if V
CC
is below 3.8V
(typical), the program function is inhibited. (b) V
CC
power
on delay— once V
CC
has reached the V
CC
sense level,
the device will automatically time out 5 ms (typical) before
programming. (c) Program inhibit— holding any one of OE
low, CE high or WE high inhibits program cycles. (d) Noise
filter— pulses of less than 15 ns (typical) on the WE or CE
inputs will not initiate a program cycle.
PRODUCT IDENTIFICATION:
The product identifica-
tion mode identifies the device and manufacturer as At-
mel. It may be accessed by hardware or software opera-
tion. The hardware operation mode can be used by an ex-
ternal programmer to identify the correct programming al-
gorithm for the Atmel product. In addition, users may wish
to use the software product identification mode to identify
the part (i.e. using the device code), and have the system
software use the appropriate sector size for program op-
erations. In this manner, the user can have a common
board design for 256K to 4-megabit densities and, with
each density’s sector size in a memory map, have the sys-
tem software apply the appropriate sector size.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both modes.
DATA POLLING:
The AT29C010A features DATA poll-
ing to indicate the end of a program cycle. During a pro-
gram cycle an attempted read of the last byte loaded will
Device Operation
(Continued)
result in the complement of the loaded data on I/O7. Once
the program cycle has been completed, true data is valid
on all outputs and the next cycle may begin. DATA polling
may begin at any time during the program cycle.
TOGGLE BIT:
In addition to DATA polling the
AT29C010A provides another method for determining the
end of a program or erase cycle. During a program or
erase operation, successive attempts to read data from
the device will result in I/O6 toggling between one and
zero. Once the program cycle has completed, I/O6 will
stop toggling and valid data will be read. Examining the
toggle bit may begin at any time during a program cycle.
OPTIONAL CHIP ERASE MODE:
The entire device
can be erased by using a 6-byte software code. Please
see Software Chip Erase application note for details.
BOOT BLOCK PROGRAMMING LOCKOUT:
The
AT29C010A has two designated memory blocks that have
a programming lockout feature. This feature prevents pro-
gramming of data in the designated block once the feature
has been enabled. Each of these blocks consists of 8K
bytes; the programming lockout feature can be set inde-
pendently for either block. While the lockout feature does
not have to be activated, it can be activated for either or
both blocks.
These two 8K memory sections are referred to as boot
blocks Secure code which will bring up a system can be
contained in a boot block. The AT29C010A blocks are lo-
cated in the first 8K bytes of memory and the last 8K bytes
of memory. The boot block programming lockout feature
can therefore support systems that boot from the lower
addresses of memory or the higher addresses. Once the
programming lockout feature has been activated, the data
in that block can no longer be erased or programmed;
data in other memory locations can still be changed
through the regular programming methods. To activate the
lockout feature, a series of seven program commands to
specific addresses with specific data must be performed.
Please see Boot Block Lockout Feature Enable Algorithm.
If the boot block lockout feature has been activated on
either block, the chip erase function will be disabled.
AT29C010A
4-131
相關PDF資料 |
PDF描述 |
|---|---|
| AT29C010 | 1 Megabit 128K x 8 5-volt Only CMOS Flash Memory |
| AT29C010A-12 | 1 Megabit 128K x 8 5-volt Only CMOS Flash Memory |
| AT29C010A | 128K x 8 5-volt Only Flash Memory(128K x 8 5V閃速存儲器) |
| AT29C020 | High Speed CMOS Logic Octal Non-Inverting Buffers and Line Drivers with 3-State Outputs 20-TSSOP -55 to 125 |
| AT29C020-10 | High Speed CMOS Logic Octal Non-Inverting Buffers and Line Drivers with 3-State Outputs 20-TSSOP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT29C010A-90TU | 功能描述:閃存 1M(128Kx8) 5V ONLY 90NS IND TEMP RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AT29C010A-90TU-T | 功能描述:IC FLASH 1MBIT 90NS 32TSOP 制造商:microchip technology 系列:- 包裝:帶卷（TR） 零件狀態:停產 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH 存儲容量:1Mb （128K x 8） 寫周期時間 - 字，頁:10ms 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TC） 安裝類型:表面貼裝 封裝/外殼:32-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:32-TSOP 基本零件編號:AT29C010 標準包裝:1,500 |
| AT29C010A-W | 功能描述:閃存 Parallel 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AT29C010-XXX | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1 Megabit 128K x 8 5-volt Only CMOS Flash Memory |
| AT29C020 | 制造商:Atmel Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。