- 您現在的位置：買賣IC網 > PDF目錄381445 > AT29BV010A-20 (Atmel Corp.) 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash PDF資料下載
參數資料
| 型號： | AT29BV010A-20 |
| 廠商： | Atmel Corp. |
| 英文描述： | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
| 中文描述： | 1兆位128K的× 8單2.7伏電池電壓的CMOS閃光 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 490K |
| 代理商： | AT29BV010A-20 |
(continued)
within the sector. The bytes may be loaded in any order;
sequential loading is not required.
HARDWARE DATA PROTECTION:
Hardware features
protect against inadvertent programs to the AT29BV010A
in the following ways: (a) V
CC
sense— if V
CC
is below 2.0V
(typical), the program function is inhibited. (b) V
CC
power
on delay— once V
CC
has reached the V
CC
sense level,
the device will automatically time out 10 ms (typical) be-
fore programming. (c) Program inhibit— holding any one
of OE low, CE high or WE high inhibits program cycles. (d)
Noise filter— pulses of less than 15 ns (typical) on the WE
or CE inputs will not initiate a program cycle.
INPUT LEVELS:
While operating with a 2.7V to 3.6V
power supply, the address inputs and control inputs
(
OE,
CE and WE) may be driven from 0 to 5.5V without ad-
versely affecting the operation of the device. The I/O lines
can only be driven from 0 to V
CC
+ 0.6V.
PRODUCT IDENTIFICATION:
The product identifica-
tion mode identifies the device and manufacturer as At-
mel. It may be accessed by hardware or software opera-
tion. The hardware operation mode can be used by an ex-
ternal programmer to identify the correct programming al-
gorithm for the Atmel product. In addition, users may wish
to use the software product identification mode to identify
the part (i.e. using the device code), and have the system
software use the appropriate sector size for program op-
erations. In this manner, the user can have a common
board design for 256K to 4-megabit densities and, with
each density’s sector size in a memory map, have the sys-
tem software apply the appropriate sector size.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both methods of identification.
Device Operation
(Continued)
Temperature Under Bias.................-55
°
C to +125
°
C
Storage Temperature......................-65
°
C to +150
°
C
All Input Voltages
(including NC Pins)
with Respect to Ground ................... -0.6V to +6.25V
All Output Voltages
with Respect to Ground .............-0.6V to V
CC
+ 0.6V
Voltage on A9
(including NC Pins)
with Respect to Ground ................... -0.6V to +13.5V
*NOTICE: Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions beyond those indi-
cated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Absolute Maximum Ratings*
DATA POLLING:
The AT29BV010A features DATA
polling to indicate the end of a program cycle. During a
program cycle an attempted read of the last byte loaded
will result in the complement of the loaded data on I/O7.
Once the program cycle has been completed, true data is
valid on all outputs and the next cycle may begin. DATA
polling may begin at any time during the program cycle.
TOGGLE BIT:
In addition to DATA polling the
AT29BV010A provides another method for determining
the end of a program or erase cycle. During a program or
erase operation, successive attempts to read data from
the device will result in I/O6 toggling between one and
zero. Once the program cycle has completed, I/O6 will
stop toggling and valid data will be read. Examining the
toggle bit may begin at any time during a program cycle.
OPTIONAL CHIP ERASE MODES:
The entire device
may be erased by using a 6-byte software code. Please
see Software Chip Erase application note for details.
BOOT BLOCK PROGRAMMING LOCKOUT:
The
AT29BV010A has two designated memory blocks that
have a programming lockout feature. This feature pre-
vents programming of data in the designated block once
the feature has been enabled. Each of these blocks con-
sists of 8K bytes; the programming lockout feature can be
set independently for either block. While the lockout fea-
ture does not have to be activated, it can be activated for
either or both blocks.
These two 8K memory sections are referred to as boot
blocks Secure code which will bring up a system can be
contained in a boot block. The AT29BV010A blocks are
located in the first 8K bytes of memory and the last 8K
bytes of memory. The boot block programming lockout
feature can therefore support systems that boot from the
lower addresses of memory or the higher addresses.
Once the programming lockout feature has been acti-
vated, the data in that block can no longer be erased or
programmed; data in other memory locations can still be
changed through the regular programming methods. To
activate the lockout feature, a series of seven program
commands to specific addresses with specific data must
be performed. Please see Boot Block Lockout Feature En-
able Algorithm.
If the boot block lockout feature has been activated on
either block, the chip erase function will be disabled.
AT29BV010A
4-5
相關PDF資料 |
PDF描述 |
|---|---|
| AT29BV010A-20JC | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
| AT29BV010A-20TC | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
| AT29BV010A-25 | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
| AT29BV010A-25JC | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
| AT29BV010A-25JI | 1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT29BV010A-20JC | 功能描述:IC FLASH 1MBIT 200NS 32PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:1M (64K x 16) 速度:150ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT29BV010A-20JI | 功能描述:IC FLASH 1MBIT 200NS 32PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:1M (64K x 16) 速度:150ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT29BV010A-20TC | 功能描述:IC FLASH 1MBIT 200NS 32TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:1M (64K x 16) 速度:150ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT29BV010A-20TI | 功能描述:IC FLASH 1MBIT 200NS 32TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:1M (64K x 16) 速度:150ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT29BV010A-25 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1 Megabit 128K x 8 Single 2.7-volt Battery-Voltage CMOS Flash |
發布緊急采購，3分鐘左右您將得到回復。