- 您現在的位置：買賣IC網 > PDF目錄362484 > AT27C4096-85DC x16 EPROM PDF資料下載
參數資料
| 型號： | AT27C4096-85DC |
| 英文描述： | x16 EPROM |
| 中文描述： | x16存儲器 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 156K |
| 代理商： | AT27C4096-85DC |
AT27C010(L)
2
The AT27C010(L) in available in a choice of industry stan-
dard JEDEC-approved one-time programmable (OTP)
plastic PDIP, PLCC, and TSOP packages. All devices fea-
ture two line control (CE, OE) to give designers the flexibil-
ity to prevent bus contention.
With 128K byte storage capability, the AT27C010(L) allows
firmware to be stored reliably and to be accessed by the
system without the delays of mass storage media.
Atmel’s 27C010(L) have additional features to ensure high
quality and efficient production use. The Rapid Program-
ming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming
time is typically only 100 μs/byte. The Integrated Product
Identification Code electronically identifies the device and
manufacturer. This feature is used by industry standard
programming equipment to select the proper programming
algorithms and voltages.
System Considerations
Switching between active and standby conditions via the
Chip Enable pin may produce transient voltage excursions.
Unless accommodated by the system design, these tran-
sients may exceed data sheet limits, resulting in device
non-conformance. At a minimum, a 0.1
μ
F high frequency,
low inherent inductance, ceramic capacitor should be uti-
lized for each device. This capacitor should be connected
between the V
CC
and Ground terminals of the device, as
close to the device as possible. Additionally, to stabilize the
supply voltage level on printed circuit boards with large
EPROM arrays, a 4.7
μ
F bulk electrolytic capacitor should
be utilized, again connected between the V
CC
and Ground
terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected
to the array.
Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AT27C040-80DC | x8 EPROM |
| AT27C040-80DI | x8 EPROM |
| AT27C040-80JC | x8 EPROM |
| AT27C040-80JI | x8 EPROM |
| AT27C040-80LC | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT27C4096-90JC | 功能描述:可擦除可編程ROM 4M bit RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| AT27C4096-90JI | 功能描述:可擦除可編程ROM 4Mb (256Kx16) OTP 5V 90ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| AT27C4096-90JU | 功能描述:可擦除可編程ROM 4Mb (256Kx16) OTP 5V 90ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| AT27C4096-90JU-T | 功能描述:IC OTP 4MBIT 90NS 44PLCC 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:EPROM 技術:EPROM - OTP 存儲容量:4Mb （256K x 16） 寫周期時間 - 字，頁:- 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TC） 安裝類型:表面貼裝 封裝/外殼:44-LCC（J 形引線） 供應商器件封裝:44-PLCC 標準包裝:1 |
| AT27C4096-90PC | 功能描述:可擦除可編程ROM 4M bit RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
發布緊急采購，3分鐘左右您將得到回復。