- 您現在的位置：買賣IC網 > PDF目錄381418 > AT25128A-10PE-2.7 (ATMEL CORP) SPI Serial Extended Temperature EEPROMs PDF資料下載
參數資料
| 型號： | AT25128A-10PE-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | SPI Serial Extended Temperature EEPROMs |
| 中文描述： | 16K X 8 SPI BUS SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001BA, DIP-8 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 390K |
| 代理商： | AT25128A-10PE-2.7 |
8
AT25128A/256A
5088C–SEEPR–11/04
Top quarter, top half, or all of the memory segments can be protected. Any of the data
within any selected segment will therefore be read only. The block write protection levels
and corresponding status register control bits are shown in Table 8.
Bits BP0, BP1, and WPEN are nonvolatile cells that have the same properties and func-
tions as the regular memory cells (e.g., WREN, t
WC
, RDSR).
The WRSR instruction also allows the user to enable or disable the write protect (WP)
pin through the use of the write protect enable (WPEN) bit. Hardware write protection is
enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is
disabled when either the WP pin is high or the WPEN bit is “0”. When the device is hard-
ware write protected, writes to the status register, including the block protect bits and the
WPEN bit, and the block-protected sections in the memory array are disabled. Writes
are only allowed to sections of the memory that are not block-protected.
NOTE:
When the WPEN bit is hardware write protected, it cannot be changed back to
“0” as long as the WP pin is held low.
READ SEQUENCE (READ):
Reading the AT25128A/256A via the SO pin requires the
following sequence. After the CS line is pulled low to select a device, the read op-code
is transmitted via the SI line followed by the byte address to be read (see Table 10).
Upon completion, any data on the SI line will be ignored. The data (D7–D0) at the spec-
ified address is then shifted out onto the SO line. If only one byte is to be read, the CS
line should be driven high after the data comes out. The read sequence can be contin-
ued since the byte address is automatically incremented and data will continue to be
shifted out. When the highest address is reached, the address counter will roll over to
the lowest address, allowing the entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE):
In order to program the AT25128A/256A, two separate
instructions must be executed. First, the device must be write enabled via the WREN
instruction. Then a Write (WRITE) instruction may be executed. Also, the address of the
memory location(s) to be programmed must be outside the protected address field loca-
Table 8.
Block Write Protect Bits
Level
Status Register Bits
Array Addresses Protected
BP1
BP0
AT25128A
AT25256A
0
0
0
None
None
1 (1/4)
0
1
3000–3FFF
6000–7FFF
2 (1/2)
1
0
2000–3FFF
4000–7FFF
3 (All)
1
1
0000–3FFF
0000–7FFF
Table 9.
WPEN Operation
WPEN
WP
WEN
Protected
Blocks
Unprotected
Blocks
Status
Register
0
X
0
Protected
Protected
Protected
0
X
1
Protected
Writeable
Writeable
1
Low
0
Protected
Protected
Protected
1
Low
1
Protected
Writeable
Protected
X
High
0
Protected
Protected
Protected
X
High
1
Protected
Writeable
Writeable
相關PDF資料 |
PDF描述 |
|---|---|
| AT25128A | High Speed CMOS Logic Quad-Bus Transceivers with 3-State Outputs 14-SOIC -55 to 125 |
| AT25256A | SPI Serial Extended Temperature EEPROMs |
| AT25128A-10PQ-2.7 | SPI Serial Extended Temperature EEPROMs |
| AT25128A-10TQ-2.7 | SPI Serial Extended Temperature EEPROMs |
| AT25128AN-10SE-2.7 | SPI Serial Extended Temperature EEPROMs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25128A-10PI-1.8 | 功能描述:IC EEPROM 128KBIT 20MHZ 8DIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT25128A-10PI-2.7 | 功能描述:IC EEPROM 128KBIT 20MHZ 8DIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT25128A-10PQ-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial Extended Temperature EEPROMs |
| AT25128A-10PU-1.8 | 功能描述:電可擦除可編程只讀存儲器 128K SPI 100K CYCLES - 10MS 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25128A-10PU-2.7 | 功能描述:電可擦除可編程只讀存儲器 128K SPI 100K CYCLES - 10MS 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。