- 您現在的位置：買賣IC網 > PDF目錄381414 > AT25010 (Atmel Corp.) 1K SPI Serial EEPROM(1K SPI串行EEPROM) PDF資料下載
參數資料
| 型號： | AT25010 |
| 廠商： | Atmel Corp. |
| 英文描述： | 1K SPI Serial EEPROM(1K SPI串行EEPROM) |
| 中文描述： | 一千的SPI串行EEPROM（每1000的SPI串行EEPROM的） |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 120K |
| 代理商： | AT25010 |
AT25010/020/040
6
Serial Interface Description
MASTER:
The device that generates the serial clock.
SLAVE:
Because the Serial Clock pin (SCK) is always an
input, the AT25010/020/040 always operates as a slave.
TRANSMITTER/RECEIVER:
separate pins designated for data transmission (SO) and
reception (SI).
MSB:
The Most Significant Bit (MSB) is the first bit
transmitted and received.
SERIAL OP-CODE:
After the device is selected with CS
going low, the first byte will be received. This byte contains
the op-code that defines the operations to be performed.
The op-code also contains address bit A8 in both the
READ and WRITE instructions.
INVALID OP-CODE:
If an invalid op-code is received, no
data will be shifted into the AT25010/020/040, and the
serial output pin (SO) will remain in a high impedance state
until the falling edge of CS is detected again. This will reini-
tialize the serial communication.
CHIP SELECT:
The AT25010/020/040 is selected when
the CS pin is low. When the device is not selected, data will
not be accepted via the SI pin, and the serial output pin
(SO) will remain in a high impedance state.
HOLD:
The HOLD pin is used in conjunction with the CS
pin to select the AT25010/020/040. When the device is
selected and a serial sequence is underway, HOLD can be
used to pause the serial communication with the master
device without resetting the serial sequence. To pause, the
HOLD pin must be brought low while the SCK pin is low. To
resume serial communication, the HOLD pin is brought
high while the SCK pin is low (SCK may still toggle during
HOLD). Inputs to the SI pin will be ignored while the SO pin
is in the high impedance state.
WRITE PROTECT:
The write protect pin (WP) will allow
normal read/write operations when held high. When the
WP pin is brought low, all write operations are inhibited.
WP going low while CS is still low will interrupt a write to the
AT25010/020/040. If the internal write cycle has already
been initiated, WP going low will have no effect on any
write operation.
The AT25010/020/040 has
SPI Serial Interface
相關PDF資料 |
PDF描述 |
|---|---|
| AT25080-10PI-1.8 | SPI Serial EEPROMs |
| AT25160-10PI-1.8 | SPI Serial EEPROMs |
| AT25320-10PI-1.8 | SPI Serial EEPROMs |
| AT25640-10PI-1.8 | SPI Serial EEPROMs |
| AT25080T1-10TC | 128 x 128 pixel format, LED or EL Backlight available |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25010_03 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25010-10PA-2.7C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|128X8|CMOS|DIP|8PIN|PLASTIC |
| AT25010-10PA-5.0C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|128X8|CMOS|DIP|8PIN|PLASTIC |
| AT25010-10PC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25010-10PC-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
發布緊急采購，3分鐘左右您將得到回復。