- 您現在的位置：買賣IC網 > PDF目錄381412 > AT24CS256-10PI-1.8 (ATMEL CORP) 2-Wire Serial EEPROMs with Permanent Software Write Protect PDF資料下載
參數資料
| 型號： | AT24CS256-10PI-1.8 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
| 中文描述： | 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 207K |
| 代理商： | AT24CS256-10PI-1.8 |
AT24CS128/256
7
Device Addressing
The 128K/256K EEPROM requires an 8-bit device address
word following a start condition to enable the chip for a read
or write operation (refer to Figure 1). The device address
word consists of a mandatory one, zero sequence for the
first five most significant bits as shown. This is common to
all 2-wire EEPROM devices.
The 128K/256K uses the two device address bits A1, A0 to
allow as many as four devices on the same bus. These bits
must compare to their corresponding hardwired input pins.
The A1 and A0 pins use an internal proprietary circuit that
biases them to a logic low condition if the pins are allowed
to float.
The eighth bit of the device address is the read/write opera-
tion select bit. A read operation is initiated if this bit is high
and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will
output a zero. If a compare is not made, the device will
return to a standby state.
DATA SECURITY:
The AT24CS128/256 has a hardware
data protection scheme that allows the user to write protect
the whole memory when the WP pin is at V
CC
.
Write Operations
BYTE WRITE:
A write operation requires two 8-bit data
word addresses following the device address word and
acknowledgment. Upon receipt of this address, the
EEPROM will again respond with a zero and then clock in
the first 8-bit data word. Following receipt of the 8-bit data
word, the EEPROM will output a zero. The addressing
device, such as a microcontroller, then must terminate the
write sequence with a stop condition. At this time the
EEPROM enters an internally-timed write cycle, t
WR
, to the
nonvolatile memory. All inputs are disabled during this write
cycle and the EEPROM will not respond until the write is
complete (refer to Figure 2).
PAGE WRITE:
The 128K/256K EEPROM is capable of 64-
byte page writes.
A page write is initiated the same way as a byte write, but
the microcontroller does not send a stop condition after the
first data word is clocked in. Instead, after the EEPROM
acknowledges receipt of the first data word, the microcon-
troller can transmit up to 63 more data words. The
EEPROM will respond with a zero after each data word
received. The microcontroller must terminate the page
write sequence with a stop condition (refer to Figure 3).
The data word address lower 6 bits are internally incre-
mented following the receipt of each data word. The higher
data word address bits are not incremented, retaining the
memory page row location. When the word address, inter-
nally generated, reaches the page boundary, the following
byte is placed at the beginning of the same page. If more
than 64 data words are transmitted to the EEPROM, the
data word address will “roll over” and previous data will be
overwritten. The address “roll over” during write is from the
last byte of the current page to the first byte of the same
page.
ACKNOWLEDGE POLLING:
Once the internally-timed
write cycle has started and the EEPROM inputs are dis-
abled, acknowledge polling can be initiated. This involves
sending a start condition followed by the device address
word. The read/write bit is representative of the operation
desired. Only if the internal write cycle has completed will
the EEPROM respond with a zero, allowing the read or
write sequence to continue.
OTP Description/Operation
The OTP feature provides the user with a 2048-bit (256 x 8)
security section, which once programmed and enabled,
becomes read-only and data cannot be changed or over-
written. The OTP section is located in the upper 2K section
of the memory array in the AT24CS128/256. If not enabled,
the OTP section will function as part of the normal memory
array.
To enable the OTP section:
1.
Inputs must be connected:
A2 = Don’t Care, A1 and A0 = V
CC
or GND
2.
Initiate the programming sequence:
START 1010 1100 11xx xxxx xxxx xxxx xxxx xxxx STOP
Once enabled, previously written data cannot be changed.
The status of the OTP section can only be confirmed by ini-
tiating a programming sequence to the OTP section and
verifying by a read command. The use of the write protect
(WP) feature can be utilized with or without enabling the
OTP function.
Read Operations
Read operations are initiated the same way as write opera-
tions with the exception that the read/write select bit in the
device address word is set to one. There are three read
operations: current address read, random address read
and sequential read.
CURRENT ADDRESS READ:
The internal data word
address counter maintains the last address accessed dur-
ing the last read or write operation, incremented by one.
This address stays valid between operations as long as the
chip power is maintained. The address “roll over” during
read is from the last byte of the last memory page, to the
first byte of the first page.
Once the device address with the read/write select bit set
to one is clocked in and acknowledged by the EEPROM,
the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but
does generate a following stop condition (refer to Figure 4).
相關PDF資料 |
PDF描述 |
|---|---|
| AT24CS128N-10SC | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
| AT24CS128N-10SC-1.8 | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
| AT24CS128N-10SC-2.7 | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
| AT24CS256W-10SC | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
| AT24CS256W-10SC-1.8 | 2-Wire Serial EEPROMs with Permanent Software Write Protect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24CS32-MAHM-E | 功能描述:IC EEPROM 32KBIT 400KHZ 8UDFN 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:EEPROM 技術:EEPROM 存儲容量:32Kb （4K x 8） 時鐘頻率:1MHz 寫周期時間 - 字，頁:5ms 訪問時間:550ns 存儲器接口:I2C 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:8-UFDFN 裸露焊盤 供應商器件封裝:8-UDFN（2x3） 標準包裝:1 |
| AT24CS32-MAHM-T | |
| AT24CS32-SSHM-B | 功能描述:IC EEPROM 32KBIT 1MHZ 8SOIC 制造商:atmel 系列:- 包裝:管件 零件狀態:有效 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K（4K x 8） 速度:400kHz，1MHz 接口:I2C，2 線串口 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:100 |
| AT24CS32-SSHM-T | 制造商:Atmel Corporation 功能描述:Atmel AT24CS32-SSHM-T EEPROM |
| AT24CS32-STUM-T | 功能描述:IC EEPROM 32KBIT 1MHZ 5SOT23 制造商:atmel 系列:- 包裝:剪切帶（CT） 零件狀態:有效 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K（4K x 8） 速度:400kHz，1MHz 接口:I2C，2 線串口 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商器件封裝:SOT-23-5 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。