- 您現在的位置：買賣IC網 > PDF目錄381405 > AT24C164 (Atmel Corp.) 2048 x 8 2-Wire Serial EEPROM(2048 x 8的2線串行EEPROM) PDF資料下載
參數資料
| 型號： | AT24C164 |
| 廠商： | Atmel Corp. |
| 英文描述： | 2048 x 8 2-Wire Serial EEPROM(2048 x 8的2線串行EEPROM) |
| 中文描述： | 2048 × 8 2線串行EEPROM（2048 × 8的2線串行EEPROM的） |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 137K |
| 代理商： | AT24C164 |
AT24C164
7
Device Addressing
The AT24C164 requires an 8-bit device address word fol-
lowing a start condition to enable the chip for read or write
operations (refer to Figure 1). The most significant bit must
be a one followed by the A2, A1 and A0 device select bits
(the A1 bit must be the compliment of the A1 input pin sig-
nal). The next 3 bits are used for memory block addressing
and select one of the eight 256 x 8 memory blocks. These
bits should be considered the three most significant bits of
the data word address. The eighth bit of the device address
is the read/write select bit. A read operation is selected if
this bit is high or a write operation is selected if this bit is
low.
Upon a compare of the device address, the EEPROM will
output a zero. If a compare is not made, the chip will return
to a standby state.
Write Operations
BYTE WRITE:
A write operation requires an 8-bit data
word address following the device address word and
acknowledgment. Upon receipt of this address, the
EEPROM will again respond with a zero and then clock in
the first 8-bit data word. Following receipt of the 8-bit data
word, the EEPROM will output a zero and the addressing
device, such as a microcontroller, must terminate the write
sequence with a stop condition. At this time the EEPROM
enters an internally-timed write cycle, t
WR
, to the nonvolatile
memory. All inputs are disabled during this write cycle and
the EEPROM will not respond until the write is complete
(refer to Figure 2).
PAGE WRITE:
The AT24C164 is capable of a 16-byte
page write. A page write is initiated the same as a byte
write, but the microcontroller does not send a stop condi-
tion after the first data word is clocked in. Instead, after the
EEPROM acknowledges receipt of the first data word, the
microcontroller can transmit up to fifteen more data words.
The EEPROM will respond with a zero after each data
word received. The microcontroller must terminate the
page write sequence with a stop condition (refer to Figure
3).
The data word address lower 4 bits are internally incre-
mented following the receipt of each data word. The higher
data word address bits are not incremented retaining the
memory page row location. When the word address, inter-
nally generated, reaches the page boundary, the following
byte is placed at the beginning of the same page. If more
than sixteen data words are transmitted to the EEPROM,
the data word address will “roll over” and previous data will
be overwritten.
ACKNOWLEDGE POLLING:
Once the internally-timed
write cycle has started and the EEPROM inputs are dis-
abled, acknowledge polling can be initiated. This involves
sending a start condition followed by the device address
word. The read/write bit is representative of the operation
desired. Only if the internal write cycle has completed will
the EEPROM respond with a zero allowing the read or
write sequence to continue.
Read Operations
Read operations are initiated the same way as write opera-
tions with the exception that the read/write select bit in the
device address word is set to one. There are three read
operations: current address read, random address read
and sequential read.
CURRENT ADDRESS READ:
The internal data word
address counter maintains the last address accessed dur-
ing the last read or write operation, incremented by one.
This address stays valid between operations as long as the
chip power is maintained. The address “roll over” during
read is from the last byte of the last memory page to the
first byte of the first page. The address “roll over” during
write is from the last byte of the current page to first byte of
the same page.
Once the device address with the read/write select bit set
to one is clocked in and acknowledged by the EEPROM,
the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but
does generate a following stop condition (refer to Figure 4).
RANDOM READ:
A random read requires a “dummy” byte
write sequence to load in the data word address. Once the
device address word and data word address are clocked in
and acknowledged by the EEPROM, the microcontroller
must generate another start condition. The microcontroller
now initiates a current address read by sending a device
address with the read/write select bit high. The EEPROM
acknowledges the device address and serially clocks out
the data word. The microcontroller does not respond with a
zero but does generate a following stop condition (refer to
Figure 5).
SEQUENTIAL READ:
Sequential reads are initiated by
either a current address read or a random address read.
After the microcontroller receives a data word, it responds
with an acknowledge. As long as the EEPROM receives an
acknowledge, it will continue to increment the data word
address and serially clock out sequential data words. When
the memory address limit is reached, the data word
address will “roll over” and the sequential read will con-
tinue. The sequential read operation is terminated when
the microcontroller does not respond with a zero but does
generate a following stop condition (refer to Figure 6).
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C16A-10PU-1.8 | 2-Wire Serial EEPROM |
| AT24C01A-10MC | 2-Wire Serial EEPROM |
| AT24C01A-10MC-1.8 | 2-Wire Serial EEPROM |
| AT24C08N-10SC | Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:TVP00; Number of Contacts:4; Connector Shell Size:21; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight |
| AT24C08N-10SC-1.8 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:TVP00; Number of Contacts:4; Connector Shell Size:21; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Body Style:Straight |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C164_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-Wire Serial EEPROM 16K (2048 x 8) |
| AT24C164-10PC | 功能描述:IC EEPROM 16KBIT 400KHZ 8DIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:32 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:1M (128K x 8) 速度:120ns 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:32-LCC（J 形引線） 供應商設備封裝:32-PLCC 包裝:管件 其它名稱:AT49BV00112JC |
| AT24C164-10PC-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C164-10PC-2.5 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C164-10PC-2.7 | 功能描述:電可擦除可編程只讀存儲器 16k 2-Wire Bus RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。