- 您現在的位置：買賣IC網 > PDF目錄381403 > AT24C11N-10SU-2.7 (ATMEL CORP) 24 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor PDF資料下載
參數資料
| 型號： | AT24C11N-10SU-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 24 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
| 中文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, LEAD AND HALOGEN FREE, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 172K |
| 代理商： | AT24C11N-10SU-2.7 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
5
AT24C11 [Preliminary]
3409B–SEEPR–12/03
Device Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an exter-
nal device. Data on the SDA pin may change only during SCL low time periods (refer to
Data Validity timing diagram). Data changes during SCL high periods will indicate a start
or stop condition as defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command (refer to Start and Stop Definition timing
diagram).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition
which terminates all communications. After a read sequence, the stop command will
place the EEPROM in a standby power mode (refer to Start and Stop Definition timing
diagram).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from
the EEPROM in 8-bit words. Any device on the system bus receiving data (when com-
municating with the EEPROM) must pull the SDA bus low to acknowledge that it has
successfully received each word. This must happen during the ninth clock cycle after
each word received and after all other system devices have freed the SDA bus. The
EEPROM will likewise acknowledge by pulling SDA low after receiving each address or
data word (refer to Acknowledge Response from Receiver timing diagram).
STANDBY MODE:
The AT24C11 features a low power standby mode which is enabled:
(a) upon power-up and (b) after the receipt of the STOP bit and the completion of any
internal operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any 2-
wire part can be reset by following these steps:
(a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then
(c) create a start condition as SDA is high.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C11-10TU-1.8 | 240 x 128 pixel format, CFL Backlight with power harness |
| AT24C11N-10SI-1.8 | 2-Wire Serial EEPROM |
| AT24C11N-10SI-2.7 | 2-Wire Serial EEPROM |
| AT24C11-10TI-1.8 | 2-Wire Serial EEPROM |
| AT24C11-10TI-2.7 | 2-Wire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C11Y1-10YU-1.8 | 功能描述:電可擦除可編程只讀存儲器 8 MAP IND TEMP 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C128 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROMs |
| AT24C128_03 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-wire Serial EEPROMs |
| AT24C128_06 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROMs |
| AT24C128_07 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Automotive Temperature Serial EEPROMs |
發布緊急采購，3分鐘左右您將得到回復。