- 您現在的位置：買賣IC網 > PDF目錄381403 > AT24C11N-10SI-1.8 (ATMEL CORP) 2-Wire Serial EEPROM PDF資料下載
參數資料
| 型號： | AT24C11N-10SI-1.8 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 2-Wire Serial EEPROM |
| 中文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 172K |
| 代理商： | AT24C11N-10SI-1.8 |
5
AT24C11 [Preliminary]
3409B–SEEPR–12/03
Device Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an exter-
nal device. Data on the SDA pin may change only during SCL low time periods (refer to
Data Validity timing diagram). Data changes during SCL high periods will indicate a start
or stop condition as defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command (refer to Start and Stop Definition timing
diagram).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition
which terminates all communications. After a read sequence, the stop command will
place the EEPROM in a standby power mode (refer to Start and Stop Definition timing
diagram).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from
the EEPROM in 8-bit words. Any device on the system bus receiving data (when com-
municating with the EEPROM) must pull the SDA bus low to acknowledge that it has
successfully received each word. This must happen during the ninth clock cycle after
each word received and after all other system devices have freed the SDA bus. The
EEPROM will likewise acknowledge by pulling SDA low after receiving each address or
data word (refer to Acknowledge Response from Receiver timing diagram).
STANDBY MODE:
The AT24C11 features a low power standby mode which is enabled:
(a) upon power-up and (b) after the receipt of the STOP bit and the completion of any
internal operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any 2-
wire part can be reset by following these steps:
(a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then
(c) create a start condition as SDA is high.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C11N-10SI-2.7 | 2-Wire Serial EEPROM |
| AT24C11-10TI-1.8 | 2-Wire Serial EEPROM |
| AT24C11-10TI-2.7 | 2-Wire Serial EEPROM |
| AT24C11-10TSI-2.7 | 2-Wire Serial EEPROM |
| AT24C11-10TU-2.7 | 2-Wire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C11N-10SI-2.7 | 功能描述:IC EEPROM 1KBIT 1MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT24C11N-10SI-2.7 SL383 | 功能描述:IC EEPROM 1KBIT 1MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT24C11N-10SI-2.7-T | 功能描述:IC EEPROM 1KBIT 1MHZ 8SOIC 制造商:microchip technology 系列:- 包裝:帶卷（TR） 零件狀態:停產 存儲器類型:非易失 存儲器格式:EEPROM 技術:EEPROM 存儲容量:1Kb （128 x 8） 時鐘頻率:1MHz 寫周期時間 - 字，頁:5ms 訪問時間:550ns 存儲器接口:I2C 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 基本零件編號:AT24C11 標準包裝:3,000 |
| AT24C11N-10SU-1.8 | 功能描述:電可擦除可編程只讀存儲器 1K 2-WIRE 1M CYCLES - 10MS 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C11N-10SU-2.7 | 功能描述:電可擦除可編程只讀存儲器 1K 2-WIRE 1M CYCLES - 10MS 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。