- 您現在的位置：買賣IC網 > PDF目錄381403 > AT24C1024-10UI-2.7 (ATMEL CORP) 640 x 480 pixel format, CCFL Backlight PDF資料下載
參數資料
| 型號： | AT24C1024-10UI-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 640 x 480 pixel format, CCFL Backlight |
| 中文描述： | 128K X 8 I2C/2-WIRE SERIAL EEPROM, PBGA8 |
| 封裝： | 0.75 MM PITCH, DBGA-8 |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 291K |
| 代理商： | AT24C1024-10UI-2.7 |
6
AT24C1024
1471H–SEEPR–03/03
Device
Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an external
device. Data on the SDA pin may change only during SCL low time periods (refer to Data
Validity timing diagram). Data changes during SCL high periods will indicate a start or stop
condition as defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition which
must precede any other command (refer to Start and Stop Definition timing diagram).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition. After a
read sequence, the Stop command will place the EEPROM in a standby power mode (refer to
Start and Stop Definition timing diagram).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl-
edge that it has received each word.
STANDBY MODE:
The AT24C1024 features a low-power standby mode which is enabled: a)
upon power-up and b) after the receipt of the STOP bit and the completion of any internal
operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any 2-wire
part can be reset by following these steps:
1.
Clock up to 9 cycles,
2.
Look for SDA high in each cycle while SCL is high.
3.
Create a start condition.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C1024W-10SI-2.7 | 2-wire Serial EEPROM 1M (131,072 x 8) |
| AT24C1024 | Octal D-Type Flip-Flops With Clear 20-TSSOP -40 to 85 |
| AT24C1024-10PI-2.7 | Octal D-Type Flip-Flops With Clear 20-TSSOP -40 to 85 |
| AT24C1024-10PU-2.7 | Two-wire Serial EEPROM |
| AT24C1024C1-10CU-2.7 | Two-wire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C1024B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM |
| AT24C1024B_08 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM 1M (131,072 x 8) |
| AT24C1024BN-SH25-B | 功能描述:電可擦除可編程只讀存儲器 8-EIAJ 2.5V NiPdAu 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C1024BN-SH25-T | 功能描述:電可擦除可編程只讀存儲器 8-EIAJ 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C1024BN-SH-B | 功能描述:電可擦除可編程只讀存儲器 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。