- 您現在的位置：買賣IC網 > PDF目錄381403 > AT24C1024-10PU-2.7 (ATMEL CORP) Two-wire Serial EEPROM PDF資料下載
參數資料
| 型號： | AT24C1024-10PU-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | Two-wire Serial EEPROM |
| 中文描述： | 128K X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, GREEN, PLASTIC, MS-001BA, DIP-8 |
| 文件頁數： | 6/18頁 |
| 文件大?。?/td> | 389K |
| 代理商： | AT24C1024-10PU-2.7 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
6
AT24C1024
1471N–SEEPR–12/05
Device
Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an external
device. Data on the SDA pin may change only during SCL low time periods (see Figure 4 on
page 7). Data changes during SCL high periods will indicate a start or stop condition as
defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition which
must precede any other command (see Figure 5 on page 8).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition. After a
read sequence, the Stop command will place the EEPROM in a standby power mode (see
Figure 5 on page 8).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl-
edge that it has received each word.
STANDBY MODE:
The AT24C1024 features a low-power standby mode which is enabled: a)
upon power-up and b) after the receipt of the stop bit and the completion of any internal
operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any two-wire
part can be reset by following these steps:
1.
Clock up to 9 cycles.
2.
Look for SDA high in each cycle while SCL is high.
3.
Create a start condition.
Device Power Up & Power Down Recommendation
POWER UP:
It is recommended to power up from 0V to full VCC in less than 1ms and then
hold for at least 100μs at full VCC level before first operation.
POWER DOWN:
It is recommended to power down from full VCC to 0V in less than 1ms and
then hold at 0V for at least 0.5s before power up. It is not recommended to VCC power down
to non-zero volt and then slowly go to zero volt.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C1024C1-10CU-2.7 | Two-wire Serial EEPROM |
| AT24C1024W-10SU-2.7 | Two-wire Serial EEPROM |
| AT24C1024-W2.7-11 | Two-wire Serial EEPROM |
| AT24C1024Y4-10YU-2.7 | Two-wire Serial EEPROM |
| AT24C1024B | Two-wire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C1024-10UI-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-wire Serial EEPROM 1M (131,072 x 8) |
| AT24C1024B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM |
| AT24C1024B_08 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM 1M (131,072 x 8) |
| AT24C1024BN-SH25-B | 功能描述:電可擦除可編程只讀存儲器 8-EIAJ 2.5V NiPdAu 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C1024BN-SH25-T | 功能描述:電可擦除可編程只讀存儲器 8-EIAJ 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。