參數資料
型號: AT24C02-10SI-1.8
廠商: ATMEL CORP
元件分類: DRAM
英文描述: 16 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
中文描述: 256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO14
封裝: 0.150 INCH, PLASTIC, SOIC-14
文件頁數: 4/14頁
文件大?。?/td> 261K
代理商: AT24C02-10SI-1.8
4
AT24C01ASC/02SC/04SC/08SC/16SC
1610B
SEEPR
04/04
Note:
1. Applicable over recommended operating range from T
A
= 0
°
C to +70
°
C, V
CC
= +2.7V to +5.5V, CL = 1 TTL Gate and 100 pF
(unless otherwise noted)
2. This parameter is characterized and is not 100% tested.
Device Operation
CLOCK AND DATA TRANSITIONS:
The SDA pin is normally pulled high with an exter-
nal device. Data on the SDA pin may change only during SCL-low time periods (see
Figure 3 on page 5). Data changes during SCL-high periods will indicate a start or stop
condition as defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition
that must precede any other command (see Figure 4 on page 6).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition.
After a read sequence, the Stop command will place the EEPROM in a standby power
mode (see Figure 4 on page 6).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. Each word requires the receiver to acknowledge that it has
received a valid command or data byte. During the transmission of commands from the
host to the EEPROM, the EEPROM will send a zero to the host to acknowledge that it
has received a valid command byte. This occurs on the ninth clock cycle of the com-
mand byte. During read operations, the host will send a zero to the EEPROM to
acknowledge that it has received a valid data byte and that it requests the next sequen-
tial data byte to be transmitted during the subsequent eight clock cycles. This occurs on
the ninth clock cycle of the data byte. If the host does not transmit this acknowledge bit,
the EEPROM will disable the read operation and return to standby mode.
STANDBY MODE:
The
AT24C01ASC/02SC/04SC/08SC/16SC feature a low-power
standby mode that is enabled upon power-up and after the receipt of the stop bit and the
completion of any internal operations.
MEMORY RESET:
After an interruption in protocol, power loss, or system reset, any
two-wire part can be reset by following these steps:
1.
Clock up to 9 cycles.
2.
Look for SDA high in each cycle while SCL is high.
3.
Create a start condition as SDA is high.
t
HD.STA
Start Hold Time
0.6
μs
t
SU.STA
Start Setup Time
0.6
μs
t
HD.DAT
Data In Hold Time
0
μs
t
SU.DAT
Data In Setup Time
Inputs Rise Time
(
2)
Inputs Fall Time
(
2)
100
ns
t
R
0.3
μs
t
F
300
ns
t
SU.STO
Stop Setup Time
0.6
μs
t
DH
Data Out Hold Time
50
ns
t
WR
Endurance
(
1)
Write Cycle Time
5
ms
5.0V, 25
°
C, Byte Mode
1M
Write Cycles
Table 4.
AC Characteristics
(1)
(Continued)
Symbol
Parameter
Min
Max
Units
相關PDF資料
PDF描述
AT24C04-10SI-1.8 16 Characters x 4 Lines, 5x7 Dot Matrix Character and Cursor
AT24C01-10TC-1.8 122 x 32 pixel format, Compact LCD size
AT24C02-10TC-1.8 122 x 32 pixel format, Compact LCD size
AT24C04-10TC-1.8 122 x 32 pixel format, Compact LCD size
AT24C01-10TI-1.8 128 x 64 pixel format, LED or EL Backlight available
相關代理商/技術參數
參數描述
AT24C02-10SI-2.5 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM
AT24C02-10SI-2.7 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM
AT24C02-10TC 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM
AT24C02-10TC-1.8 功能描述:電可擦除可編程只讀存儲器 2k 2-Wire Bus RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
AT24C02-10TC-2.5 制造商:Atmel Corporation 功能描述:256 X 8 I2C/2-WIRE SERIAL EEPROM, 4500 ns, 8 Pin Plastic SOP