參數資料
型號: AT24C01AY6-10YH-1.8
廠商: ATMEL CORP
元件分類: DRAM
英文描述: Two-wire Serial EEPROM
中文描述: 128 X 8 I2C/2-WIRE SERIAL EEPROM, DSO8
封裝: 2 X 3 MM, 0.50 MM PITCH, GREEN, MO-229, MLP-8
文件頁數: 10/26頁
文件大?。?/td> 617K
代理商: AT24C01AY6-10YH-1.8
10
AT24C01A/02/04/08A/16A
0180Z–SEEPR–11/06
ACKNOWLEDGE POLLING:
Once the internally timed write cycle has started and the
EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a
start condition followed by the device address word. The read/write bit is representative of the
operation desired. Only if the internal write cycle has completed will the EEPROM respond
with a zero allowing the read or write sequence to continue.
Read
Operations
Read operations are initiated the same way as write operations with the exception that the
read/write select bit in the device address word is set to one. There are three read operations:
current address read, random address read and sequential read.
CURRENT ADDRESS READ:
The internal data word address counter maintains the last
address accessed during the last read or write operation, incremented by one. This address
stays valid between operations as long as the chip power is maintained. The address “roll
over” during read is from the last byte of the last memory page to the first byte of the first page.
The address “roll over” during write is from the last byte of the current page to the first byte of
the same page.
Once the device address with the read/write select bit set to one is clocked in and acknowl-
edged by the EEPROM, the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but does generate a following stop condi-
tion (see Figure 10 on page 12).
RANDOM READ:
A random read requires a “dummy” byte write sequence to load in the data
word address. Once the device address word and data word address are clocked in and
acknowledged by the EEPROM, the microcontroller must generate another start condition.
The microcontroller now initiates a current address read by sending a device address with the
read/write select bit high. The EEPROM acknowledges the device address and serially clocks
out the data word. The microcontroller does not respond with a zero but does generate a fol-
lowing stop condition (see Figure 11 on page 12).
SEQUENTIAL READ:
Sequential reads are initiated by either a current address read or a ran-
dom address read. After the microcontroller receives a data word, it responds with an
acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment
the data word address and serially clock out sequential data words. When the memory
address limit is reached, the data word address will “roll over” and the sequential read will con-
tinue. The sequential read operation is terminated when the microcontroller does not respond
with a zero but does generate a following stop condition (see Figure 12 on page 12).
相關PDF資料
PDF描述
AT24C04Y6-10YH-1.8 Two-wire Serial EEPROM
AT24C08AY6-10YH-1.8 Two-wire Serial EEPROM
AT24C01B Two-wire Serial EEPROM
AT24C02AN-10SQ-2.7 The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
AT24C04A The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
相關代理商/技術參數
參數描述
AT24C01B 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM
AT24C01B_08 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM 1K (128 x 8)
AT24C01B_09 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Automotive Temperature Serial EEPROM
AT24C01B-10PU-2.7 制造商:Atmel Corporation 功能描述:
AT24C01BN-SH-B 功能描述:電可擦除可編程只讀存儲器 1K 2-WIRE 128 x 8 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8