- 您現在的位置：買賣IC網 > PDF目錄381406 > AT24C01A-10TI-1.8 (ATMEL CORP) 128 x 64 pixel format, LED or EL Backlight available PDF資料下載
參數資料
| 型號： | AT24C01A-10TI-1.8 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 128 x 64 pixel format, LED or EL Backlight available |
| 中文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | 4.40 MM, PLASTIC, MO-153AA, TSSOP-8 |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 445K |
| 代理商： | AT24C01A-10TI-1.8 |
6
AT24C01A/02/04/08A/16A
0180V–SEEPR–8/05
Device Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an exter-
nal device. Data on the SDA pin may change only during SCL low time periods (see
Figure 4 on page 7). Data changes during SCL high periods will indicate a start or stop
condition as defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command (see Figure 5 on page 8).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition.
After a read sequence, the stop command will place the EEPROM in a standby power
mode (see Figure 5 on page 8).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has
received each word. This happens during the ninth clock cycle.
STANDBY MODE:
The AT24C01A/02/04/08A/16A features a low-power standby mode
which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the
completion of any internal operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any 2-
wire part can be reset by following these steps:
1.
Clock up to 9 cycles.
2.
Look for SDA high in each cycle while SCL is high.
3.
Create a start condition.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C08-10TI-1.8 | 128 x 64 pixel format, LED or EL Backlight available |
| AT24C16-10TI-1.8 | 128 x 64 pixel format, LED or EL Backlight available |
| AT24C01A-10TU-1.8 | 240 x 128 pixel format, CFL Backlight with power harness |
| AT24C08AU2-10UU-1.8 | B&K Digital Multimeter Accuracy:0.5%; Display Technology:LCD; Frequency Measuring Range:100Hz to 10kHz Z540 CALIBRATION RoHS Compliant: NA |
| AT24C16AU2-10UU-1.8 | Digital Multimeter; DMM Type:Handheld; Calibrated:No; Frequency Measuring Range:100Hz to 100KHz; Accuracy:0.005; Display Technology:LED RoHS Compliant: NA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C01A-10TI-2.5 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C01A-10TI-2.7 | 功能描述:IC EEPROM 1KBIT 400KHZ 8TSSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:378 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:8M（1M x 8，512K x 16） 速度:110ns 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-CBGA 供應商設備封裝:48-CBGA（7x7） 包裝:托盤 |
| AT24C01A-10TI-2.7 SL383 | 功能描述:IC EEPROM 1KBIT 400KHZ 8TSSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT24C01A-10TI-2.7-T | 功能描述:IC EEPROM 1KBIT 400KHZ 8TSSOP 制造商:microchip technology 系列:- 包裝:帶卷（TR） 零件狀態(tài):停產 存儲器類型:非易失 存儲器格式:EEPROM 技術:EEPROM 存儲容量:1Kb （128 x 8） 時鐘頻率:400kHz 寫周期時間 - 字，頁:5ms 訪問時間:900ns 存儲器接口:I2C 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:8-TSSOP 基本零件編號:AT24C01 標準包裝:3,000 |
| AT24C01A-10TSU-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Two-wire Serial EEPROM |
發(fā)布緊急采購，3分鐘左右您將得到回復。