- 您現在的位置：買賣IC網 > PDF目錄381399 > AT24C01-10PI-2.7 (ATMEL CORP) 2-Wire Serial EEPROM PDF資料下載
參數資料
| 型號： | AT24C01-10PI-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | 2-Wire Serial EEPROM |
| 中文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001BA, DIP-8 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 261K |
| 代理商： | AT24C01-10PI-2.7 |
9
AT24C01ASC/02SC/04SC/08SC/16SC
1610B
–
SEEPR
–
04/04
will the EEPROM respond with a
“
0
”
(ACK), allowing the read or write sequence to
continue.
Read Operations
Read operations are initiated the same way as write operations, with the exception that
the read/write select bit in the device address word is set to
“
1
”
. There are three read
operations: current address read, random address read, and sequential read.
CURRENT ADDRESS READ:
The internal data word address counter maintains the
last address accessed during the last read or write operation, incremented by one. This
address stays valid between operations as long as the chip power is maintained. The
address
“
rollover
”
during read is from the last byte of the last memory page to the first
byte of the first page. The address
“
rollover
”
during write is from the last byte of the cur-
rent page to the first byte of the same page.
Once the device address with the read/write select bit set to
“
1
”
is clocked in and
acknowledged by the EEPROM, the current address data word is serially clocked out.
The microcontroller does not respond with an input
“
0
”
but does generate a following
stop condition (refer to Figure 9)
Figure 9.
Current Address Read.
RANDOM READ:
A random read requires a
“
dummy
”
byte write sequence to load in the
data word address. Once the device address word and data word address are clocked
in and acknowledged by the EEPROM, the microcontroller must generate another start
condition. The microcontroller now initiates a current address read by sending a device
address with the read/write select bit high. The EEPROM acknowledges the device
address and serially clocks out the data word. The microcontroller does not respond
with a
“
0
”
(NO ACK) but does generate a following stop condition (refer to Figure 10).
Figure 10.
Random Read
Note:
* = DON
’
T CARE bit for 1K)
S
T
A
R
T
SDA LINE
M
S
B
L
S
B
R
/
W
A
C
K
DATA
N
O
A
C
K
DEVICE
ADDRESS
R
E
A
D
WORD
ADDRESS n
L
S
B
A
C
K
M
S
B
L
S
B
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C01-10SC | 2-Wire Serial EEPROM |
| AT24C01-10SC-2.5 | 2-Wire Serial EEPROM |
| AT24C01-10SC-2.7 | 2-Wire Serial EEPROM |
| AT24C01-10SI | 2-Wire Serial EEPROM |
| AT24C01-10SI-2.5 | 2-Wire Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C01-10SA-5.0C | 制造商:Atmel Corporation 功能描述:24C01-10SA-5.0C |
| AT24C01-10SC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C01-10SC-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C01-10SC-2.5 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
| AT24C01-10SC-2.7 | 功能描述:電可擦除可編程只讀存儲器 1K (128X8) 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。