- 您現在的位置：買賣IC網 > PDF目錄381396 > AT17C256A-10JI (ATMEL CORP) FPGA Configuration EEPROM PDF資料下載
參數資料
| 型號： | AT17C256A-10JI |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | FPGA Configuration EEPROM |
| 中文描述： | 256K X 1 CONFIGURATION MEMORY, PQCC20 |
| 封裝： | PLASTIC, LCC-20 |
| 文件頁數： | 3/11頁 |
| 文件大?。?/td> | 159K |
| 代理商： | AT17C256A-10JI |
AT17A Series
3
Pin Configurations
PLCC/S
OIC
DIP
Pin
Pin
Name
I/O
Description
2
1
DATA
I/O
Three-state DATA output for reading. Input/Output pin for programming.
4
2
CLK
I
Clock input. Used to increment the internal address and bit counter for reading and
programming.
8
3
RESET/OE
RESET/Output Enable input (when SER_EN is High). A low level on both the CE and
RESET/OE inputs enables the data output driver. A high level on RESET/OE resets both
the address and bit counters. A logic polarity of this input is programmable as either
RESET/OE or RESET/OE. This document describes the pin as RESET/OE.
9
4
CE
I
Chip Enable input. Used for device selection. A low level on both CE and OE enables the
data output driver. A high level on CE disables both the address and bit counters and
forces te device into a low-power mode. Note this pin will not enable/disable the device in
2-wire serial mode (ie; when SER_EN is low).
10
5
GND
Ground pin
12
6
CEO
O
Chip Enable Out output. This signal is asserted low on the clock cycle following the last
bit read from the memory. It will stay low as long as CE and OE are both low. It will then
follow CE until OE goes high. Thereafter, CEO will stay high until the entire PROM is
read again and senses the status of RESET polarity.
A2
I
Device selection input, A2. This is used to enable (or select) the device during
programming and when SER_EN is low (see Programming Guide for more details).
18
7
SER_EN
I
Serial enable is normally high during FPGA loading operations. Bringing SER_EN low,
enables the 2-wire serial interface for programming.
20
8
V
CC
+3.3V/+5V power supply pin.
Absolute Maximum Ratings*
Operating Temperature..................................-55°C to +125°C
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature.....................................-65°C to +150°C
Voltage on Any Pin
with Respect to Ground............................. -0.1V to V
CC
+
0.5V
Supply Voltage (V
CC
) .......................................-0.5 V to + 7.0V
Maximum Soldering Temp. (10 sec. @ 1/16 in.).............260
°
C
ESD (R
ZAP
= 1.5K, C
ZAP
= 100 pF)................................. 2000V
相關PDF資料 |
PDF描述 |
|---|---|
| AT17C65A-10JC | FPGA Configuration EEPROM |
| AT17C65A-10JI | FPGA Configuration EEPROM |
| AT17LV128A | High Speed CMOS Logic 4-Bit Parallel Access Register 16-TSSOP -55 to 125 |
| AT17LV65A | High Speed CMOS Logic 3-to-8 Line Decoder Demutiplexer with Address Latches 16-PDIP -55 to 125 |
| AT17A | FPGA Configuration EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT17C512 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:FPGA Configuration E2PROM Memory |
| AT17C512-10CC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EEPROM |
| AT17C512-10CI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EEPROM |
| AT17C512-10JC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:FPGA Configuration E2PROM Memory |
| AT17C512-10JI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:FPGA Configuration E2PROM Memory |
發布緊急采購，3分鐘左右您將得到回復。