- 您現在的位置：買賣IC網 > PDF目錄381396 > AT17C128A-10JC (ATMEL CORP) FPGA Configuration EEPROM PDF資料下載
參數資料
| 型號： | AT17C128A-10JC |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | FPGA Configuration EEPROM |
| 中文描述： | 128K X 1 CONFIGURATION MEMORY, PQCC20 |
| 封裝： | PLASTIC, LCC-20 |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 159K |
| 代理商： | AT17C128A-10JC |
AT17A Series
2
Controlling The AT17A Series Serial EEPROMs
Most connections between the FPGA device and the serial
EEPROM are simple and self-explanatory.
The DATA output of the AT17A Series drives DIN of the
FPGA devices.
The master FPGA CCLK output drives the CLK input of
the AT17A Series.
The CEO output of any AT17C/LV128/256A drives the
CE input of the next AT17C/LV65/128/256 in a cascade
chain of PROMs.
SER_EN must be connected to V
CC
.
There are, however, two different ways to use the inputs
CE and OE, as shown in the AC Characteristics wave-
forms.
Condition 1
The simplest connection is to have the FPGA D/P output
drive both CE and RESET/OE in parallel (Figure 1). Due to
its simplicity, however, this method will fail if the FPGA
receives an external reset condition during the configura-
tion cycle. If a system reset is applied to the FPGA, it will
abort the original configuration and then reset itself for a
new configuration, as intended. Of course, the AT17A
Series does not see the external reset signal and will not
reset its internal address counters and, consequently, will
remain out of sync with the FPGA for the remainder of the
configuration cycle.
Condition 2
The FPGA D/P output drives only the CE input of the
AT17A Series, while its OE input is driven by the inversion
of the input to the FPGA RESET input pin. This connection
works under all normal circumstances, even when the user
aborts a configuration before D/P has gone high. A high
level on the RESET/OE input to the AT17C/LVxxxA – dur-
ing FPGA reset – clears the Configurator's internal address
pointer, so that the reconfiguration starts at the beginning.
The AT17A Series does not require an inverter since the
RESET polarity is programmable.
Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AT17LV128A-10JC | FPGA Configuration EEPROM |
| AT17C128A-10JI | FPGA Configuration EEPROM |
| AT17LV128A-10JI | FPGA Configuration EEPROM |
| AT17C128A | FPGA Configuration EEPROM |
| AT17C256A | FPGA Configuration EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT17C128A-10JI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:FPGA Configuration EEPROM |
| AT17C256 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:FPGA Configuration E2PROM |
| AT17C256-10CC | 功能描述:FPGA-配置存儲器 ASICS RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| AT17C256-10CI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EEPROM |
| AT17C256-10JC | 功能描述:FPGA-配置存儲器 RO 556-AT17LV25610JC RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
發布緊急采購，3分鐘左右您將得到回復。