- 您現在的位置：買賣IC網 > PDF目錄379680 > AS3842N13 (Electronic Theatre Controls, Inc.) Current Mode Controller PDF資料下載
參數資料
| 型號： | AS3842N13 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Current Mode Controller |
| 中文描述： | 電流模式控制器 |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 155K |
| 代理商： | AS3842N13 |
20
ASTEC Semiconductor
instabilities caused by the low amplitude of the
current sense ramp waveform. In such a case,
any noise on the waveform can be sufficient to
trip the comparator resulting in random and pre-
mature pulse termination. The addition of a small
amount of artificial ramp (slope compensation)
can eliminate such problems without drastically
affecting the overall performance of the system.
2.3 Circuit layout and other
considerations
The electronic noise generated by any switch-
mode power supply can cause severe stability
problems if the circuit is not layed-out (wired)
properly. Afew simple layout practices will help to
minimize noise problems.
When building prototype breadboards, never use
plug-in protoboards or wire wrap construction.
For best results, do all breadboarding on double
sided PCB using ground plane techniques. Keep
all traces and lead lengths to a minimum. Avoid
large loops and keep the area enclosed within
any loops to a minimum. Use common point
grounding techniques and separate the power
ground traces from the signal ground traces.
Locate the control IC and circuitry away from
switching devices and magnetics. Also, the tim-
ing capacitors ground connection must be right
at pin 5 as shown in Figure 15. These grounding
and wiring techniques are very important
because the resistance and inductance of the
traces are significant enough to generate noise
glitches which can disrupt the normal operation
of the IC.
Also, to provide a low impedance path for high
frequency noise, V
CC
and V
REF
should be decou-
pled to IC ground with 0.1 μF capacitors. Addi-
tional decoupling in other sensitive areas may
also be necessary. It is very important to locate
the decoupling capacitors as close as possible to
the circuit being decoupled.
AS384x
Current Mode Controller
相關PDF資料 |
PDF描述 |
|---|---|
| AS4LC1M16E5-50JC | 3V 1M X 6 CMOS DRAM (EDO) |
| AS4LC1M16E5-50JI | 3V 1M X 6 CMOS DRAM (EDO) |
| AS4LC1M16E5-50TC | 3V 1M X 6 CMOS DRAM (EDO) |
| AS4LC1M16E5-50TI | 3V 1M X 6 CMOS DRAM (EDO) |
| AS4LC1M16E5-60JC | 3V 1M X 6 CMOS DRAM (EDO) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS3842NT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode Controller |
| AS3843 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode Controller |
| AS3843D1413 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode Controller |
| AS3843D14T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current Mode Controller |
| AS3843D-8 | 制造商:Astec Semiconductor 功能描述:Swithed-Mode Power Supply Controller, Current Mode Type, Bi-Polar, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。