- 您現在的位置：買賣IC網 > PDF目錄381305 > AS1369-BWLT-33 (AUSTRIAMICROSYSTEMS AG) 200mA Micro-Sized; Package Type: CS-WLP(1x1)-4; Output Range: 3.3V PDF資料下載
參數資料
| 型號： | AS1369-BWLT-33 |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 200mA Micro-Sized; Package Type: CS-WLP(1x1)-4; Output Range: 3.3V |
| 封裝： | CS-WLP(1x1)-4 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 789K |
| 代理商： | AS1369-BWLT-33 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁
17 - 21
AS1369
Datasheet - Application Information
8.6.2 Output Capacitor ESR
The series regulator is a negative feedback amplifier, and as such is conditionally stable. The ESR of the output capacitor is usually used to
cancel one of the open loop poles of the error amplifier in order to produce a single pole response. Excessive ESR values may actually cause
instability by excessive changes to the closed loop unity gain frequency crossover point. The range of ESR values for stability is usually shown
either by a plot of stable ESR versus load current, or a maximumvalue in the datasheet.
Some ceramc capacitors exhibit large capacitance and ESR variations with variations in temperature. Z5U and Y5V capacitors may be required
to ensure stability at temperatures below T
AMB
= -10°C. With X7R or X5R capacitors, a 1μF capacitor should be sufficient at all operating
temperatures.
Larger output capacitor values (10μF) help to reduce noise and improve load transient-response, stability and power-supply rejection.
8.6.3 Input Capacitor
An input capacitor at V
IN
is required for stability. It is recommended that a 1.0μF capacitor be connected between the AS1369 power supply
input pin V
IN
and ground (capacitance value may be increased without limt subject to ESR limts). This capacitor must be located at a distance
of not more than 1cmfromthe V
IN
pin and returned to a clean analog ground. Any good quality ceramc, tantalum or filmcapacitor may be used
at the input.
8.6.4 Noise
The regulator output is a DC voltage with noise superimposed on the output. The noise comes fromthree sources; the reference, the error
amplifier input stage, and the output voltage setting resistors. Noise is a randomfluctuation and if not mnimzed in some applications, will
produce systemproblems.
8.6.5 Transient Response
The series regulator is a negative feedback system and therefore any change at the output will take a finite time to be corrected by the error
loop. This “propagation time” is related to the bandwidth of the error loop. The initial response to an output transient comes fromthe output
capacitance, and during this time, ESR is the domnant mechanismcausing voltage transients at the output. More generally:
Units are Volts, Amps, Ohms.
(EQ 16)
Thus an initial +50mA change of output current will produce a -12mV transient when the ESR=240m
. Remember to keep the ESR within
stability recommendations when reducing ESR by adding multiple parallel output capacitors.
After the initial ESR transient, there follows a voltage droop during the time that the LDO feedback loop takes to respond to the output change.
This drift is approx. linear in time and sums with the ESR contribution to make a total transient variation at the output of:
Units are Volts, Seconds, Farads, Ohms.
(EQ 17)
Where:
C
LOAD
is output capacitor
T= Propagation Delay of the LDO
This shows why it is convenient to increase the output capacitor value for a better support for fast load changes. Of course the formula holds for
t < “propagation time”, so that a faster LDO needs a smaller cap at the load to achieve a simlar transient response. For instance 50mA load
current step produces 50mV output drop if the LDO response is 1usec and the load cap is 1μF.
There is also a steady state error caused by the finite output impedance of the regulator. This is derived fromthe load regulation specification
discussed above.
8.6.6 Turn On Time
This specification defines the time taken for the LDO to awake fromshutdown. The time is measured fromthe release of the enable pin to the
time that the output voltage is within 5% of the final value. It assumes that the voltage at VIN is stable and within the regulator mn and max limts.
Shutdown reduces the quiescent current to very low mostly leakage values (<1μA).
8.6.7 Thermal Protection
To prevent operation under extreme fault conditions, such as a permanent short circuit at the output, thermal protection is built into the device.
Die temperature is measured, and when a 150°C threshold is reached, the device enters shutdown. When the die cools sufficiently, the device
will restart (assumng input voltage exists and the device is enabled). Hysteresis of 20°C prevents low frequency oscillation between start-up and
shutdown around the temperature threshold.
V
TRANSIENT
I
OUTPUT
R
ESR
=
V
TRANSIENT
I
OUTPUT
R
ESR
C
LOAD
-------T
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| AS13985F12-T | 150mA Low-Noise LDO; Package Type: CS-WLP(1x1.4)-5; Output Range: 1,2V |
| AS13985F18-T | 150mA Low-Noise LDO; Package Type: CS-WLP(1x1.4)-5; Output Range: 1,8V |
| AS13985F26-T | 150mA Low-Noise LDO; Package Type: CS-WLP(1x1.4)-5; Output Range: 2,6V |
| AS13985F27-T | 150mA Low-Noise LDO; Package Type: CS-WLP(1x1.4)-5; Output Range: 2,7V |
| AS13985F28-T | 150mA Low-Noise LDO; Package Type: CS-WLP(1x1.4)-5; Output Range: 2,8V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS1369-BWLT-33-10K | 制造商:AMS 功能描述:IC REG LDO 3.3V 0.2A 4WLCSP |
| AS1369BWLT33-10K | 制造商:AMS 功能描述:IC REG LDO 3.3V 0.2A 4WLCSP |
| AS1369BWLT33-1K | 制造商:AMS 功能描述:IC REG LDO 3.3V 0.2A 4WLCSP |
| AS1369-BWLT-45 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:200mA Ultra-Compact Low Dropout Regulator |
| AS1369-BWLT-50 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:200mA Ultra-Compact Low Dropout Regulator |
發布緊急采購，3分鐘左右您將得到回復。