- 您現在的位置：買賣IC網 > PDF目錄381303 > AS1329C-BTTT (AUSTRIAMICROSYSTEMS AG) Adj. 315mA, 1.2MHz Boost feed.; Package Type: TSOT23-6; Miscellaneous: Continuous Switching PDF資料下載
參數資料
| 型號： | AS1329C-BTTT |
| 廠商： | AUSTRIAMICROSYSTEMS AG |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Adj. 315mA, 1.2MHz Boost feed.; Package Type: TSOT23-6; Miscellaneous: Continuous Switching |
| 中文描述： | 低電壓，微功耗，型DC - DC升壓轉換器 |
| 封裝： | TSOT23-6 |
| 文件頁數： | 14/21頁 |
| 文件大小： | 990K |
| 代理商： | AS1329C-BTTT |
wwwaustriamcrosystems.com/DC-DC_Step-Up/AS1329
Revision 1.11
14 - 21
AS1329
Datasheet - Application Information
9.3 External Component Selection
9.3.1 Inductor Selection
The fast switching frequency (1.2MHz) of the AS1329 allows for the use of small surface mount or chip inductor for the external inductor
(see
Figure 19 on page 8)
.
The required mnimumvalues for the external inductor are:
!
3.3μH for applications
≤
3.6V
!
4.7μH for applications > 3.6V
Larger inductor values allow greater output current capability by reducing the inductor ripple current. Increasing the inductance above 10μH will
increase size while providing negligible improvement in output current capability.
The approximate output current capability of the AS1329 versus inductor value is given in:
Where:
η
is the estimated efficiency;
I
P
is the peak current limt value (0.6A);
V
IN
is the input voltage;
D is the steady-state duty ratio = (V
OUT
- V
IN
)/V
OUT
;
f is the switching frequency (1.2MHz typ);
L is the inductor value.
The inductor current ripple is typically set for 20 to 40% of the maximuminductor current (I
P
). High-frequency ferrite core inductor materials
reduce frequency dependent power losses compared to less expensive powdered iron types, which result in improved converter efficiency.
The inductor should have low ESR to reduce the I2R power losses, and must be able to handle the peak inductor current without saturating.
Molded chokes and some chip inductors normally do not have enough core to support the peak inductor currents of the AS1329 (850mA typ). To
mnimze radiated noise, use a toroid, pot core, or shielded bobbin inductor.
Table 6. Recommended Inductors
Part Number
MOS6020-103ML
MOS6020-472ML
MOS6020-332ML
CDRH4D18-100
CDRH4D18-6R8
CR43-6R8
CDRH4D18-4R7
L
DCR
93m
Ω
50m
Ω
46m
Ω
200m
Ω
200m
Ω
131.2m
Ω
162m
Ω
Current Rating
1A
1.5A
1.8A
0.61A
0.76A
0.95A
0.84A
Dimensions (L/W/T)
6.8x6.0x2.4mm
6.8x6.0x2.4mm
6.8x6.0x2.4mm
6.9x5.0x2.0mm
6.9x5.0x2.0mm
4.8x4.3x3.5mm
6.9x5.0x2.0mm
Manufacturer
10μH
4.7μH
3.3μH
10μH
6.8μH
6.8μH
4.7μH
wwwcoilcraft.comSumda
wwwsumda.com
(EQ 2)
I
OUT MAX
)
η
I
P
IN
D
f L 2
V
–
1
D
–
(
)
=
相關PDF資料 |
PDF描述 |
|---|---|
| AS1331-BTDT-AD | 300mA Buck-Boost Converter; Package Type: TDFN(3x3)-10; Output Range: 2.5 to 3.3V |
| AS1331-BTDT-33 | 300mA Buck-Boost Converter; Package Type: TDFN(3x3)-10; Output Range: 3.3V |
| AS1332-BWLT | 650mA, RF Buck Converter, Vcon |
| AS1333-BWLT | 650mA, RF, Buck Converter; Package Type: CS-WLP(1.5x1.5)-8; Output Range: 3.09V |
| AS1334-BTDT-30 | 650mA LowRipple Buck Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AS1329C-TT_EK_ST | 功能描述:AS1329C - DC/DC, Step Up 1, Non-Isolated Outputs Evaluation Board 制造商:ams 系列:- 零件狀態:有效 主要用途:DC/DC，步升 輸出和類型:1，非隔離 功率 - 輸出:- 電壓 - 輸出:3.3V 或 5V 電流 - 輸出:570mA 電壓 - 輸入:0.85 V ~ 5 V 穩壓器拓?fù)?升壓 頻率 - 開關:1.2MHz 板類型:完全填充 所含物品:板 使用的 IC/零件:AS1329C 標準包裝:1 |
| AS132R4FLF | 制造商:TT Electronics / IRC 功能描述:AS132R4FLF |
| AS132R4HLF | 制造商:TT Electronics / IRC 功能描述:AS132R4HLF |
| AS132R4JLF | 制造商:TT Electronics / IRC 功能描述:AS132R4JLF |
| AS1330 | 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:4MHz, Low Voltage, DC-DC Step-Up Converter |
發布緊急采購，3分鐘左右您將得到回復。